By Steve Herschbach
The battery door of the Minelab Gold Monster 1000 has a loop of steel wire that acts as a safety to keep the door from getting lost. I needed a temporary fix for another problem and stole the loop off my GM1000. The wire loop looked like it might be handy for many things, and I vaguely remembered seeing them someplace. Finally tracked it down as a keychain or luggage tag loop. Picked up a pack of 20 on Amazon for just $7.49 including shipping. For 0.37 each it just seemed like something I could use in my tool box.
By Steve Herschbach
This subject has been mentioned before here but it seems some people are having issues that may go beyond the "norm", whatever that is. See Bill Southern's forum at http://nuggetshooter.ipbhost.com/topic/30883-mike-c-falsing-fix/
My 5" coil starts to exhibit touch sensitivity at Manual Sensitivity level 9, becoming more pronounced at 10. I have had no issue of note with my 10" coil, which is the coil I use almost exclusively. My impression has been this touch sensitivity in the 5" coil is inherent in the High Gain/Audio Boosted design of the GM1000. For me the solution had been to either lower the Gain/Sensitivity or to just get down and dirty with coil control. See my post from May at http://www.detectorprospector.com/forum/topic/3614-understanding-the-sensitivity-control-on-the-gold-monster-1000/?do=findComment&comment=39955 as regards all this.
Any experienced detectorist knows a loose coil cable near the coil can create problems, and Mike Conner has suggested affixing the coil cable on the 5" coil as firmly as possible to prevent movement in the cable, with what he reports as being good results.
This has been a non-issue for me as I run the 10' coil almost exclusively and my sensitivity when in manual ranges between 6 - 8 with rare forays to higher levels as described in my recent thread here. My main concern is reports of 5" coil touch sensitivity at much lower Gain/Sensitivity levels than what I have experienced. So the big question for you Gold Monster owners (no second hand reports please) - what coil sensitivity are you experiencing and at what Gain/Sensitivity level does it start to exhibit with each coil? Have you tried more firmly affixing the lower cable to the rod, and has it helped?
By Cabin Fever
Thought I would post on how I modified a GPX shaft to make it a little more compact. I cut roughly 6" off the end and drilled 7 more holes in the shaft so the lower poll would go further up into the upper shaft. Now my Monster shortens up to about 30" and extends to 4 feet. I now have lots of adjustment options from extra short to full length. I also picked up an extra lower poll to keep the second coil mounted. Changing coils is a pet peeve of mine so I like to keep it quick and simple. I've been on 4 short hunts now with this setup and can't be more happy.
By Steve Herschbach
I purchased a Golden Mask telescoping rod with the intent of using it for my Deus HF elliptical coil. XP placing the battery in the trapezoidal lower rod section however made an adaptation more trouble than it is worth for something I am not sure I will keep anyway. I decided to repurpose it instead to the Minelab Gold Monster 1000 in an attempt to make it as easy as possible to collapse down and put in a rucksack.
The arm cup removal is easy. Just remove the bolts. The grip/handle however is both screwed together and glued. Have to give them credit - beautifully made rod assembly. Some heat from a hair dryer and careful prying got the grip assembly off the rod.
The upper rod is thicker than the standard rod diameter and so the neat little clamps Minelab includes with the GM1000 will not work. Instead standard hose clamps will serve until I get some that fit better.
The upper rod is not quite long enough to get the proper spacing for the armrest, so this is a mockup until I find a short piece of rod the correct diameter to install in the upper rod for a little extra length. Roughly 30" long when collapsed. The coil needed to be shimmed with an extra rubber washer. I used the skinny little Golden Mask plastic bolt but will drill the isolator rod out to accommodate the Minelab bolt later.
Near final product, with way more length fully extended than I need at my height of 5'11" but that is good for working overhead cut banks and poking around in the brush. Click all photos for larger versions. Once I get the rough edges finished this will be a sweet little backpacker unit.
So the pup and I headed out to some of my favorite bench areas above the creek; good thing I checked the depth of the water at the crossing before trying to take the side x side through like I normally did in previous years....mid-thigh high, so carried gear and pup to other side and hiked just under a mile to first site:
A granite nob that's been hit by myself and several friends the past couple seasons, but it still keeps squeaking out little tiddlers:
Got a couple there, then moved one to another spot where several more were found after moving some of the old-timers hand-stackings:
Don't need a gym membership when you do this as a hobby! :-)
Anyway, hit a few more areas with some success, but the creme de la creme (or should I say, creme de la crumb?) was this area I dug for hours and cleaned out at least 25 tiny bits....what fun the Monster was having! (To better get in under the roots etc, the Goldbug2 would have been better, but we managed)
The next day and a half hit a couple more spots and ended up with this for my Bench Tour Total.....a lot of work(i.e. fun) for 1.4g lol!
Pup and I had a great few days at the cabin.....but it's time to get the zed and 2300 out again, so off to California later this week!
Cheers and Happy Hunting!
p.s. kiwijw, I was inspired by your posts! :-)