Jump to content

Recommended Posts

MSRP: $149.00 MAP: $129.00

Dealers are accepting pre-orders for the F-Pulse as of Monday, Nov. 13th with a late November early December ship date.

fisher-f-pulse-metal-detecting-pinpointer.jpg

The F-Pulse is completely waterproof to 10 feet and capable of operating in fresh and saltwater.

Features:
• Pulse Induction
• Beep, vibrate or both
• Lost mode alarm
• Single button operation
• 3 sensitivity levels
• Proportional response
• Retune
• Adjustable LED light
• Auto shutdown
• 2-AA batteries (not included)
• Belt holster included
• 2-year warranty
• Constructed from special
abrasion-resistant materials
(won’t wear through like other pinpointers)

  • Like 1

Share this post


Link to post
Share on other sites

I am in line for one of these. The fact it is a PI pinpointer is enough for me to give it a go. Why the Fisher instead of Teknetics? I actually prefer the green as nice on the eyes, but red is just far easier to find if accidently dropped in the woods. Not something I normally do but cheap insurance! Not sure when it will get here (sometime in next couple weeks?) but when it does I will report back.

  • Like 1

Share this post


Link to post
Share on other sites

Steve, please keep us posted when you get yours.  Be nice to do air test between the Garrett and the Fisher.

 

Share this post


Link to post
Share on other sites

It being a PI pinpointer I would not think air tests will be great. The way to test this thing will be in bad ground (which I have). It it can punch just a bit deeper than my Garrett Carrot than they have a winner. Though being a PI pinpointer another concern will be machine interference.

I am not sure when they are shipping - next week or two?

Share this post


Link to post
Share on other sites
12 hours ago, Steve Herschbach said:

It being a PI pinpointer I would not think air tests will be great. The way to test this thing will be in bad ground (which I have). It it can punch just a bit deeper than my Garrett Carrot than they have a winner. Though being a PI pinpointer another concern will be machine interference.

I am not sure when they are shipping - next week or two?

Air hots are pretty good (nickel @ 3+" @ med sens) and should be the same in ground. It has a frequency offset adjust (16 levels) so you can minimize interference.

  • Like 3
  • Thanks 1

Share this post


Link to post
Share on other sites

Thanks Carl, can’t wait to get mine! I assume you had a hand in this massive improvement in FT pinpointers :smile:

Share this post


Link to post
Share on other sites
22 hours ago, Geotech said:

Air hots are pretty good (nickel @ 3+" @ med sens) and should be the same in ground. It has a frequency offset adjust (16 levels) so you can minimize interference.

Wow that sounds awesome, my Garrett Pro Pointer gets 1 7/8" on a US nickel.  Thanks Carl.

 

Share this post


Link to post
Share on other sites

Still waiting for my new pinpointer so I am guessing that late November/early December ship thing did not happen.

Share this post


Link to post
Share on other sites

well I just bought a Pro Pointer AT a few weeks ago not knowing this one was coming, my fault, should have done more research, this one is likely to be better too for a very similar price, either way I'm happy with my AT so it's here to stay.

 

Share this post


Link to post
Share on other sites
On 12/16/2017 at 9:02 PM, Steve Herschbach said:

Still waiting for my new pinpointer so I am guessing that late November/early December ship thing did not happen.

 

On 12/16/2017 at 9:02 PM, Steve Herschbach said:

Still waiting for my new pinpointer so I am guessing that late November/early December ship thing did not happen.

I ordered mine dec18 but can only guess as to when it will be shipped. I hope it at least comes by the time my EQ800 arrives

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By Steve Herschbach
      Pro-Pointer AT Z-Lynk Instructional Video - Basic features and functions of the fully wireless Pro-Pointer AT Z-Lynk pinpointer are demonstrated. Sections include: wireless syncing; a tip on factory reset; adjusting detection and sensitivity settings; lost pinpointer alarm; retuning the Pro-Pointer to find targets faster or to overcome environmental challenges; battery replacement; and general care.

       
    • By Ridge Runner
      A friend took his Pro Find for a little water detecting for the first time. The trouble started when his pinpointer started acting up but then went dead . At first he was thinking the battery went dead but knew better when water came running out of the battery compartment. He looked the case over good and he could see a hair line crack on one side in the seam .
      He told me after this happen and looking at it again one could see the seam wasn’t fused good together. I guess you could call a factory defect and wouldn’t been known until maybe never if it didn’t go swimming.
      Thanks for warranty we get .
      Chuck
    • By “Spartan800”
      Hi fellow detectorists!
      I am completely a novice to Metal detecting. This is my current setup: 
      Minelab Equinox 600 and a trenching shovel from Home Depot.
      After roughly 15 hours of use without a pin pointer, I have come to the conclusion I NEED A PIN POINTER. As of today 17APR18 I purchased the FISHER F-PULSE and was curious present day, how those of you that use this pin pointer how it’s function is to a newbie like myself. I have have read several forum discussions by Steve, calcobra, geotech and many more. Thank you all for your indirect quantifiable background experience that has helped me immensely!
      Sorry for this long post I just know you all are the subject matter experts when it comes to this new hobby I’ve ventured into. Oh by the way, I’m looking for fellow metal detectorists in the NC area. 
      Thank you all🙂🇺🇸🙂
    • By SittingElf
      I received the 35 barely used from a member here at a great price. On arrival, I tested it against my Garrett Carrot, and find it much easier to use, with better adjustment ease, as well as being capable of deeper activation on coins. The non-ferrous capability is phenomenal, and it is designed not to affect your detector while riding on your belt.

      Speaking of belts...the one thing I really DON'T like is the very narrow and tight belt loop on the holster. I would have much preferred the Molle-capable snap and velcro style of the Garrett. Someone wasn't thinking at Minelab. It won't fit on any wide belt.  I may have it modified with a velcro fold-over and snap.

      All in all, a fantastic new Pinpointer, and I think my Garrett will end up in my son's or wife's MD equipment...at least for now!
    • By SittingElf
      Thinking about using PlastiDip for protecting the tip of my pinpointers and extending their life.

      Anyone tried that? Looking for experience and views.
      Cheers

    • By SittingElf
      Looking for a Pro-Find 35 in stock...along with a lot of other people!
      Dealers monitoring this forum could help if you'd post when you have stock!
      Cheers!
×