Jump to content
Sign in to follow this  
riden2low

Coil Compatibility

Recommended Posts

Any one know if the ctx coils interchange with the equinox beside the mounting on the shaft?

 

 

Share this post


Link to post
Share on other sites

Welcome to the forum!

CTX or any other coils will not work on Equinox. Only coils make specifically for the machine will work on it. Those include the 11” round DD that comes with it, the 6” round DD that we will see in the next couple months, and the 12” x 15” DD that will hopefully appear before the end of summer.

6FFF8547-58DD-4863-B76B-3FAD3525975E.jpeg

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Similar Content

    • By Nuke em
      Hi , does anyone know what the difference is between Park 1 and Park 2 modes ? 
      I need a mode that i can use on dry beaches away from the salt wet. But i have to put it into frequency 10 khts to match the Terra .
      Its mainly for looking for coinage in shingle and sand beaches . 
      I need depth and sensitivity .
      Thanks
    • By Hobo
      Am I doing something wrong? I cant get the volume control + or  -- buttons to work on the ML80 phones. The volume works fine on the detector.
    • By MCH2
      Streamlining
      At the moment I am a quantity clad hunter. Just looking for more efficient ways of operating. Currently I am using the Equinox 600 with wireless low latency headphones.  I use park mode 1 with 50 tones and leave open VDI numbers 13, and 24 to 38.   My method: I mostly bend at the waist with a little knee flex to dig (no kneeling); most coins are less than 5" deep. I use a Lesche 10" hand trowel and a smaller wider trowel for popping near surface coins. I only bend over once per target. I use a pinpointer after initial coil pinpointing leaving the pinpointer on facing away from the target while digging, dig target, pinpoint again as needed, recover target, turn pinpointer off, fill in hole, pick up tools, then straighten back up, pocket finds, holster tools and give the hole a final step on and start sweeping again. I have gone from using the pinpointer holster to using my back pants pocket as this is faster to draw and replace without having to stop and look to holster. Also started using a quicker holster for my larger trowel and keep my small wider trowel in my other back pocket. I use a small tie on hardware apron with a pocket for finds and a pocket for trash.  My 600 is tethered to my belt with an elastic bungee cord so it hangs and moves with me when I bend and straighten up; it never gets laid on the ground.
      Anyone like to share their method of streamlining to increase efficiency and cut down on redundancy.
       Malcolm
    • By Belgy1972
      Now that we've all had a bit of time to enjoy the Nox whether that be the 600 or 800.
      Which mode do you think is the best and why, more to the point what do you think the benefits are over the other modes. I prefer park 2 as i find with the right sweep speed there is very little falsing compared to the others especially field 2.
    • By midalake
      Can someone tell me how long the coil wire is? Coil through connector,
       
      Thanks Dave
    • By Nuke em
      On Youtube i saw from another forum link that a bloke has found another way to check for bad targets on his 600 . I assume its the same for the 800 .
      The Minelab Equinox 'Hack' - Target ID Trick.
      Starts at 1.49 minutes
       
×