Jump to content

Minelab GPZ 7000 Brochure 2015

Sign in to follow this  

1 Screenshot




  • Similar Content

    • By phrunt
      I always wondered if there was even gold around where the X-coil manufacturer lives, I didn't know much about Russian gold or if Russia even had much gold.
      Here is a video broken into parts of the Russian manufacturer showing the different capabilities of the 17x12" X-Coil between the Standard GPZ14” Minelab coil being used near high voltage power lines in Russia.
      It's good to see he is a prospector.
      Sorry about the quality of some of the parts. 
      It's a deep hole he has to dig to get it, nice soft soil though... that'd make life easier than using a jackhammer 🙂
       
    • By Emmanuel
      Hello fellow prospectors,
      I recently acquired a Minelab GPZ 7000 and I am looking for a fellow prospector wanting to search for gold with me in Southern California. As a former FBI agent, I have learned it is better to have two people when exploring unknown places... I have been using a Minelab CTX 3030 and I am ready for something new i.e. gold prospecting. I live in Long Beach but  I also have a home in the Lake Arrowhead area (San Bernardino County). I believe some areas are worth prospecting in San Bernardino County. Having said that, I am willing to travel. Reach out if you are interested. ads4350@gmail.com
    • By jasong
      I was going to post this in one of the X Coil threads, but it might be of interest to everyone.
      I bought a replacement ferrite ring since I left my ML ferrite in Arizona. It's one of the Doc's ferrites with the white backside (off Ebay), I did not realize they were not ML ferrites when I bought it. The OEM Minelab ferrites have a black backside.
      It would not balance on the X Coils at all and actually sounded like a screaming target (I didn't try the Z14) so I reported that to the coil manufacturer. He responded that the white backed aftermarket rings are not the same as the ML rings. So, as I normally do, I checked for myself, bought an authentic ML ring, and he was right.
      They are the same size, but the Doc's ring is 10 grams heavier (something I noticed immediately but did not have a ML ring to compare to until recently). It is also more magnetic. The Doc's ring is also conductive whereas the ML ring is non-conductive - the Doc's ring was reading about 38 ohms from side to side whereas the ML ring read infinity. And after I sanded the backs to get a fresh surface to check resistances on I noticed the ML ring looks dull and black as a ferrite should, but the Doc's ring looks shiny and metallic, like iron.
      So, clearly there are differences between the two rings. Thought people might like to know even if you are just using the stock coil, as I'm not sure how this affects the ground balance, but someone could be running suboptimally using this ring.

    • By Jin
      I often see others using a high sensitivity setting of 16 - 20 on the 7000. Is there really much of an advantage doing this? I used to think maxing out my 4500 gave me some kind of advantage over the poor suckers who ran factory presets or slightly higher, now im not so convinced. 
      Today i tested out my new 10" and 20" X-coils and tried many different combinations of settings to see what would suite me best. I did most of my testing with the 20" coil on a 2 gram bit of gold. I dug a skinny trench 200mm (nearly 8 inches) in some reasonably hot ground and placed my 2 gram bit in the bottom. High yield/Difficult were the better settings. (Ferrite and ground balanced, Semi auto ground balance,  Ground/audio smoothing off,  volume 8 (using a booster),  threshold 27,  threshold pitch 63,  volume limit 7)
      First i tried a high sensitivity and the target signal popped out nice and loud. Then I started detecting the surrounding area and felt there was so much other ground noises going on that the quieter signals may be masked. Eventually I found my sweet spot where the detector was quiet as a mouse and i had no problems hearing a slight change in the threshold no matter how small it was. This was at a sensitivity of only 3.
      I then went back over the 2 gram bit and it still gave a great response using sensitivity of 3 (although slightly less than when the sensitivity was a lot higher).
      When i started detecting and raising the sensitivity up around 6 -8 a lot more ground noise came in. Now im used to ground noise as i used to use my gpx in Normal timings most of the time. But after reading how the zed is a different beast and not to drive it to hard i decided to try less aggressive settings to see if less is infact more. Obviously im new to the zed and have much to learn so will continue trying different things until i get my head around things. 
        
    • By phrunt
      Here is a recent video of a couple of dudes testing out their massive range of Nugget Finder coils against the GPZ 7000 on targets they've dug into the ground in Western Australia's red dirt.  I found it quite an interesting video and shows how close a lot of coils are in performance.
      I notice he doesn't appear to scrub the GPZ on the ground as much as the others, not sure the reason for that, maybe he doesn't want to damage such an expensive coil ?
      By the time he's got to the GPZ all the ground scrubbing has probably made it a shallower target.
×
×
  • Create New...