Jump to content

Has The Sea Ghost Housing Been Discussed On This Forum?

Recommended Posts

Do you know if it continues to manufacture?  A colleague has written to him on Facebook and he does not respond to messages or connect

Link to post
Share on other sites

On 5/3/2021 at 12:00 AM, JRJR said:

Can you show where the charging cable attaches with and without the cable attached?






  • Like 1
Link to post
Share on other sites
On 5/3/2021 at 11:15 PM, Airtemisa said:

I considered this mod in my first equinox 800, but finally I sold it and get a new one... Only for the warranty. 

Those who have the SeaghostMod, what can you say about the Equinox for diving? Anyone compared it with Excalibur?


This eq mod is not really for diving, but you can easily take it 10m deep. Headphones a pretty loud.

Link to post
Share on other sites
  • 1 month later...
On 12/7/2020 at 8:22 AM, pjrough said:

I am Ukraine born, but currently located in EU. 

Unfortunately the EQ kit is not DIY type of product, so you have to ship your detector to Ukraine. Ones the modificación is ready you are getting back ready to use equinox along with a charging cable, waterproof headphones and the grip.

There is the same story happen with vanquish: you have to ship it. There are some soldering to be done, thus kit is not suitable for self installation.

Although some older housings (explorer/etrac series) were suitable for DIY assembly.

Different installation variants are available. Here is my EQ600 (pot is made by seaghost, the rest is done by me):



What is your opinion of the waterproof headphones supplied by Sea Ghost?

Link to post
Share on other sites
On 6/8/2021 at 4:13 AM, JRJR said:

What is your opinion of the waterproof headphones supplied by Sea Ghost?

Very loud and well-built. Coiled cable is soft.

Link to post
Share on other sites
On 5/5/2021 at 4:26 PM, Luis said:

Do you know if it continues to manufacture?  A colleague has written to him on Facebook and he does not respond to messages or connect

I saw a post on his FB page recently that another customer from Italy or Spain (don’t remember) is going to run his page or social media stuff?  Maybe time?  I’m sure this guy has a day job and doesn’t make a living off of these. I do wish there was a more informative site on this product and how to go about getting it.  I’m sure there is some level of skepticism or worry to send an expensive detector to a guy you don’t know in Russia and a few hundred bucks and hope you get it back..

  • Like 1
Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Content

    • By 1515Art
      I know Steve has already posted a direct link to purchase a 6000 protective cover directly from Australia, I just ordered this one off of eBay that claims to be made down under and sold directly from Double D fulfilled by eBay. If you are looking for said metal detector cover here is the eBay link to the Dbl D cover.
    • By Jerry Perez
      Does anyone have the dimensions for the control box of the Fisher CZ-3D or the Fisher M-66 Valve and Box Locator? I'm looking for a dust rain cover for the Gold Bug 2 and since they don't make the dust cover anymore for he gb2 I'm looking for an alternate solution other than custom making one. It looks like the CZ-3D or the M-66 could be similar dimensions with the GB2 but don't know. Then again I can't find a dust cover for either of them either, geez!
      The Gold Bug 2 control box is: 5" Deep x 3" High x 4.5" Wide
      Any feedback is greatly appreciated.

    • By Nvgoldhunter
      good morning and happy new year to all!!
      I'm sure this question has been asked many times in the past, but I was hoping someone could refresh mu memory. I'm currently swinging a gpx 5000 with a commander 15 x 12 mono coil -- ( old school). I wear out the covers a lot and have had problems getting new ones recently---so question is whats the best way to get the most from my covers??? I 've heard truck beeding stuff works good --- make a new bottom from fiberglass --- or ????
      Thanks all good luck
    • By kac
      Wanted to give the Multi Kruzer a go with the Superfly coil at the beach. Kept the machine in 5khz, manual ground balance as it would drift with tracking on. Was a little bit noisier in spots compared to the stock but on the damn and dry sand it had excellent depth with very stable numbers. Gain was kept around 93 without issue even in the wet.
      One thing I didn't like is if I got any water behind the scuff it would false a bit but outside of that its a good combo.
      Managed to sneak out a Barber dime at 10" in the damp sand in my my 3 hour run, called it a day when I broke my scoop handle.

    • By stevejhgla
      How can I prevent my headphone jack from further corrosion?
      A little back story. 
      I'm submerging my equinox 800 about 2-3 times per week in saltwater (Florida gulf coast).  
      Purchased the LS PELSO headphones October 11th (1 week shipping) and as you can see they have already started to corrode. 
      I don't take the headphones out and wash the jack EVERYTIME. (Trying to avoid this)
      Please leave a comment, let me know what you do, and what you think will work for me! 

    • By Ryan
      Well I have now gone through a second GPZ stock coil cover. Has anyone tried out the Nugget Finder coil cover for the 14x13 and if so how have you liked it? I am either looking at one of these or somehow modifying my stock cover to extend the life. If the stock covers were only $10 I could justify the reoccurring cost but at almost $50 ..not really.   Thanks
  • Create New...