Jump to content

Recommended Posts


So true!!👍

  • Like 2
  • Haha 2
Link to post
Share on other sites

I want everyone to know that I have yet farted out loud in a public place. I must admit my pucker power is getting weaker!

 Guys some how we’ve got to get back on the subject of detecting. You can tell it’s hot outside due to our off key subject matter.

 Getting old is not for the weak because you got to be strong to make it.

 Like Always The Best To All Here On The Forum!

 Chuck 

  • Like 4
  • Haha 2
Link to post
Share on other sites

Not sure if I farted out loud in public,  can't hear them anymore!

                                                                       Norm

  • Like 2
  • Haha 7
Link to post
Share on other sites

For you young fellas, take no notice of all the old fellas, the best side of 60 is from 60 up. Now what was I on about............

  • Like 4
  • Haha 1
Link to post
Share on other sites

Well ,I sure don't have much to look forward to by the look of it.  At least in my 50's I'll get a s sports car, although that was done in my 20's so maybe I'll end up with a Volvo instead.  I'm not much of a car person though, I buy one and use it until it dies, it's probably the thing I care least about as to me it's just a mode of transport.

I just hope in my detecting lifetime a PI comes out with accurate Target ID's, if it does I'll be satisfied.  A PI CTX 3030 and I'd be satisfied.   I'd like if it draws the outline of the target on the screen as you waive over it too with some sort of ground penetrating radar technology!   The more swipes over it the more detailed the image becomes.  Ahhhh, I can stop dreaming now, that can be my sports car in my 50's, a detector of my dreams.

  • Like 7
  • Haha 2
Link to post
Share on other sites

HA!

I can confess to being a little over pressurized in public spaces at sundry times in my past, to other's merriment and my embarrassment.  I'm still trying to live down the un-expected outburst at the CPR/First-aid training event.

HH
Mike

 

 

  • Like 2
  • Haha 5
Link to post
Share on other sites

    I say we are on topic! Detecting the joke of the day!😁 And yes, with the heat, and current events, we all need a little more laughter to lighten the mood, and keep us detecting/prospecting, and forum strong! Steve will slap us in line, if he objects! He appreciates a good laugh, as much as anyone, I'm sure! Within parameters, of course!

*Besides, I really enjoyed sending this to my 86 year old dad! Thanks!!👍👍

  • Like 5
Link to post
Share on other sites

Well I don’t care who you are are how old but if you hear your name called and you don’t get there soon it’s too bad. I won’t go into explaining it to you but if it hadn’t happen yet it will. One day you’ll be sitting there and say I know now what’s Chuck’s talking about.haha 

Chuck 

  • Haha 3
Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Content

    • By Carolina
      Mailed my detector to California today. Going to find out why it won’t turn off at times or won’t turn on at times outdoors in 80+ degrees. Indoors 70 degrees works like it should. I will post the results.
    • By cuniagau
      I have sent an e-mail to Felix at FT with these pictures.  Hopefully they just send me a new rod ASAP.  This is what happens when you hunt wet sand and California surf.  Or it could just have been a poor quality made rod.  Hoping for that latter as the wet sand California surf is the only place I have to use the Impulse AQ and don't want to have to worry about this again.



    • By bklein
      I have an EQ600 with a full set of coils. I was at Laguna yesterday with the large coil. I am using bluetooth earbuds that have been recommended by others. There was a lot of black sand where I was hunting. I was having the detect audio stutter like it was overloading bluetooth or the headset although I played with the detector audio and couldn’t reduce the stutter. There also seemed to be indications of a bad coil connection at the coil. Wiggle it a bit and you hear a crackle.  Never got a full disconnect though. I later ran all metal and maybe the stutter was less not sure. In disc I was stock settings masking zero and below.  But that should be a nice audio cancel - should hear good targets without them being chopped up. I found stuff but it was a miserable detecting experience. I played with recovery speed and went between beach 1 and 2 modes.  Tried messing with ground balance types too.  I found that if I was in black sand areas pinpoint would help me locate possible targets and I’d just dig them without much clue from Lcd ID or tone (running 50 tones).  I didn’t have the other coils with me to test. I tried sensitivity 17 on up. Normally was 22/23.  I was experiencing bad latency with the earbuds that I don’t remember being an issue with the 11” coil.  Just a real test of my brain the whole day.
    • By Dirk Digger
      I either need someone to help me find a manual to download for the original bandido (not 2) or I need info on what the little black knob is on the back of the control housing. Maybe how to ground balance it. General information about it.


    • By schoolofhardNox
      Does anyone know specifically what goes wrong with the Garrett AT pin pointers? Both of mine were sent in previously, and both of them developed the same issue again. They turn on but do not detect any metal. Is it the electrolytic capacitor, the flat pack The IC or is it in the coil itself that is the problem? Is that long rod a radio frequency coil? I'm kinda getting tired of pin pointers dying like that. Any ideas would be helpful.
    • By Canarias_detection
      Hello, I had a problem with my metal detector, I was using it in the water, after several months it does not turn on and shows the message "CD" on the screen and then you can see the water inside ..
      the guarantee I change it for another without problems a fast process
        I have read, that water enters through the union of the handle to the pda (subjecting screws to the mast), according to what they say, this problem only happens to those made in Malaysia ... those made in Australia do not have that problem, the first series they come out perfect
      does anyone know about this topic?
      How do I know where my detector was manufactured?
      I can attach photos of the box (where the manufacture comes) and compare with other users..thanks
      my detector is equinox 800 February 2020



×
×
  • Create New...