Jump to content

GPX 6000 Running A 15x10" X-coil


Recommended Posts


12 minutes ago, afreakofnature said:

Is that one of yours, unchipped?

No, it's in Russia, and it's using the chip from a standard coil, the chip from the standard coil was removed to do this, and they would require an adapter to run.

At some point I'll certainly be using one with these coils, I want small coils for my detecting, this 15x10" is one of my favourite coils though, I like elliptical shaped coils for detecting here with our rocky terrain.

  • Like 2
Link to comment
Share on other sites

2 minutes ago, afreakofnature said:

🤔. A chip and an adapter, not just a chip?

The chip goes into an adapter, maybe I worded it so it doesn't make sense 🙂

 

Link to comment
Share on other sites

Just now, afreakofnature said:

I see, not built in the coil.  So maybe sacrifice a coil for a chip to build an adapter plug.

You could still use the original coil without the chip.  Just some open heart surgery 😉

  • Like 4
Link to comment
Share on other sites

Hi Phrunt, So is the chip cut from within an original coil & that coil then mended over with the chip being used to make an adapter in a same/similar way as the gpz 7000 X coil adapter that is then on the outside of the coil.  So the chip is going from the inside of the coil to the outside in the form of an inline coil cable adapter & able to be interchanged between ML GPX coils & X coils? I guess the adapter would be at the top end connection going into the control box? Interesting. I am picking that the 15x10 X coil is a mono.

 

Thank you

 

Greg.

Link to comment
Share on other sites

Just now, dig4gold said:

So the chip is going from the inside of the coil to the outside in the form of an inline coil cable adapter & able to be interchanged between ML GPX coils & X coils?

That's right, the chip is removed from the original coil by surgery 🙂 And then an adapter is made in a similar way to the GPZ X-coil adapter, up near the control box the original coil cable is cut, and the chip is added inline as part of the plug that goes into the detector so the adapter becomes a universal adapter to run the X-coils.  All early days so far but progress for those that want different coils and are willing to do the adjustments necessary.

  • Like 5
Link to comment
Share on other sites

Thanks. Guess that will ruffle a few feathers just like I noticed the GPZ 7000 X coil adapter did. Was only a matter of time I suppose before the Russians did this for the 6000. Will give the detecting community more options, which is a good thing isn't it?

 

Greg

  • Like 1
  • Thanks 1
Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
  • Similar Content

    • By Aureous
      Seeing how this topic has numerous mentions across the internet, what are the range of faults exhibited? My nearest dealer is over an hour from me so I don't want to travel back and forth after picking mine up if I get a faulty one. So I know what to look for after collection and field test. 
    • By oldcoinhunter
      My first 6000 was faulty out of the box which they replaced with a new one. I've had the new one for 21 days and probably used it 8 days before it went bad.  When i was boxing it up to ship back i heard something rattling inside of it, not good. In researching i found that they've known them to have major issues since March or April, yet they have refused to address the issue with a production stop or at least look at the different production runs and recall those units. I think when it's all said and done there will be a substantial number of them that are faulty worldwide. As it stands now, Detector Center states that there is a" temporary" 10- 14 day time frame for repairing them. My bet is that it's not going to be temporary. If this failure rate continues there may be grounds for a worldwide class action lawsuit, who knows. Oh, and i owned a business for 40 years. Not a very smart way to run a business. JMO.
    • By Gerry in Idaho
      Well my staff/I just finished the season and wrap up of field training for 2021 and our customers...and boy did it go out with a bang and big belly's thanks to Chef Rusty Bucket.  Smoked ribs, Bourbon shrimp in garlic sauce, berry pie and ice cream, smoked Brisket, bacon wrapped stuffed jalapenos and more.  Wish I would have taken more pics of the food.  As I have said before, the food/drinks/people are part of why I enjoy these trips, as I know the gold will eventually come.
      As many know, Gerry’s Detectors has been training out there at the burn barrel with a few different staff members since the 90’s.   We have been using just about every model of gold detector from the top manufactures as well as coils to see what the best results are.  The comparisons of customers detectors continue to see the improvements of technologies and capabilities which is what we want.  Yes there are times a more expensive detector may not produce the best signal response on that particular targets, but it’s what it is and part of learning.
      Some of what we found most amazing and it’s exactly what I expected would happen during the training at RP.  The gold nuggets being found during the 3 days of class was the most of any session in at least 5+ yrs.  More people went home with actual Rye Patch gold than what my staff/I have witnessed in quite a long time.  The knowledge shared was the same stuff we always go over, but the knowledge retained was higher.  The class size is usually around the same, but the amount of golden smiles of success was better than many yrs prior.  We know the VLF detectors when fit with small coils are going to find a few pickers, but to see the bigger PI machines perform so well and produce such higher %’s of beautiful NV gold was most impressive.
      So lets go over it again to see what my Staff/I observed, in no particular order.  Knowledge of customers detectors was actually retained, smiles of happy customers making the right choice of detectors, the amount of successful customers who went home with gold and the overall numbers of gold nuggets dug by the students.  There is one thing that I corollate all these positives and it’s the new GPX-6000, period.
      Yes we had SDC-2300’s, GPZ-7000, GPX-5000’s and the usual VLF’s in the class being learned by the students and those who were there with the GPX-6000 had the most Success.  But the success of gold nugget finds was just part of the fun.  Ease of operation and simplicity we’ve never seen from a PI Minelab was also most impressive.  The customers were actually not afraid of their detectors.  They didn’t worry if the timing and or sequence of adjustments was correct, as the GPX-6000 is pretty much a turn on and go.  The old way, a big multi page instruction manual (is missing) and now we get a 3 step Quick Start…and it’s true.  1) Turn On.  2) Raise/Lower Coil for 10s, 3) Begin Detecting.  Are you kidding me, no way that can’t be true.  We just paid $6000 for one of the latest technology fine tuned gold detectors in the world and all we get in the box to help learn, is 3 short steps with a combined total of 10 words?  
       
      Well folks,  it’s all true and so is the amount of happy customers who invested in our training and the new GPX-6000.
      If anyone thinks there was some other reason for the above, please chime in as all indicators are bulls eyed at the GPX-6000.  Overall the trip went exceptionally well consider the 100 yr rain storm that came through while we were down there.  I still love the natural beauty of Northern NV in the fall and the colors on the gold nuggets we dug.
      Hopefully the Spring/Summer class will be just as productive with a group of new enthusiastic customers and more gold being unearthed.









    • By Rob Allison
      Hello All,
          The new Minelab 17" Elliptical Searchcoils for the Minelab GPX 6000 have been flying off the shelves, definitely high demand.   Due to the high demand, I haven't had much time to use one, everyone ends of taking mine ... LOL
      I haven't seen much larger gold being found at depth yet, but I'm sure it is.  Curious how people and past customers are doing with this new 17" Searchcoil beyond covering more ground quicker?  
      We still have a few left in stock from the last large shipment and more on the way if anyone is still searching for a new "Christmas present.!"  Hahaha 
      Would love to see some pictures or at least hear about any success with the new searchcoil.  
      Wishing you all much success on the goldfield.
      Rob
    • By billdean
      Each time I try and ground balance my 6000 there is no detectable change. While holding the GB button I pump the coil then move it side to side. It’s like it don’t work. I friend of mine says his does not either. What am I missing? I run in manual mode with the threshold on. The noise cancel works very well. 
    • By billdean
      This is from Steve’s GPX 6000 accessories page. 
       
      The following items do not come with the GPX 6000, but are likely to work with it based on what is known so far. This is preliminary guesswork, and it is not advised a purchase be made based solely on the information presented here.
      https://parts.minelab.com/0302-0082-p/0302-0082.htm
×
×
  • Create New...