I've read several threads on the soon-to-be-fielded Deus 2 and how it will compare to the Equinox. There have been many good views on this topic so I thought I'd share mine. As you read this, keep in mind the views expressed here are worth just as much as you've paid for them. 😁
1. Wireless vs Wired: I'm 99% a salt water beach hunter with my EQX 800 and the way I grid a beach, I often go from the damp sand to the wet sand and then into the surf (only about 1 foot deep due to concerns over water intrusion so I keep the control box dry). Given that, a Deus II for me would have to be constantly wired from coil to control box in order to work in the surf. For that reason, a totally wireless capability would not be that enticing since the wire from coil to box would be a permanent configuration.
2. Waterproof: I owned a Deus and found it to be a solidly engineered machine so I'm not a skeptic where XP claims of being waterproof are concerned. Were I to make a wager, I'd bet on much better waterproof performance in the Deus II than was the original ML waterproof claim for the EQX. Being truly waterproof is important for me and not because I hunt deeper than 1 foot in salt water these days because I don't. Ours is an outdoor hobby so I think all detectors should be waterproof...at the very least, reliably weatherproof. How many times have you been caught in the rain or dropped your detector in a puddle of water? Even if you are a land hunter and never go near any water, replacing a damaged or inop machine due to moisture intrusion isn't a trivial thing.
3. Build quality: The Deus I had was quality built, rugged and reliable. No coil ear issues, wobbly shafts or arm cuff breakage. In my view, it was a much more rugged detector than Minelab products in certain areas. XP doesn't seem to pinch pennies as did Minelab on simple things. Recall the original skimpy gaskets they put in the CTX 3030 that caused flooding of the battery box. The issue was solved when they came out with merely a little thicker gasket! Their use of cheap coil ears, arm cuffs and wobbly shafts on the EQX series is another example. For a few pennies more per unit, they would have saved untold thousands in warranty replacement costs in both the CTX and EQX series machines. Although they are among the very best where software technology is concerned, I never understood that "penny wise pound foolish" approach in their physical build design.
4. Overall Performance: This is where the EQX was superior to my original Deus. The multi-frequency/multi IQ of the EQX vs the selectable single frequency of the Deus was an obvious choice in my salt water beach hunting environment. I eventually sold my Deus for that reason. Now, if XP has really overcome that limitation in the Deus II with their FMF feature, I'll be happily impressed.
5. Final Thoughts: I'm with the others who will take a "wait and see" approach. But, given my past experience with XP engineering, I have no doubt the Deus II will be a very capable salt water beach detector. Will it generally outperform the Minelabs? TBD. Will it be found that XP pinched pennies on their build quality? I say no. It will be a well built unit. Will it be more comfortable to use than the Minelabs? Yes. Will it be more complex in its settings options than the Minelabs? Yes. Will it's overall performance justify the higher price tag compared to the current EQX? TBD but that will be determined solely by and in the eye of the beholder as the saying goes.
Just a few thoughts from my foxhole...
By UT Dave
I'd like to increase my knowledge and skill in tuning my Nox 800 for specific conditions.
Those of you who tune your machines off the factory defaults, please share what you have! Not what your settings are, but how you arrive at those settings.
For instance, is there a relationship between different settings, such, that a preferred order of operations is suggested for optimal results? I noise cancel, then ground grab, then adjust sensitivity. FE2, Recovery, Threshold, is there a best practice for the order in which they are set?
How do you know when you should increase or decrease FE2 or Recovery? What factors or indicators go into that decision?
I've arrived at my current default beginning state, by trying to make things first "worse" in my test garden. By adjusting each setting individually up and down though the full range of adjustment, noting whether signal got better or worse at each step, to get what I considered the best signal on a deep silver coin. But doing so in a controlled situation with a known target like that is one thing, knowing how to read variable conditions and how to tune accordingly is quite another.
How do you make your tuning decisions in the field? What are the settings you most frequently find need adjusted to accommodate search conditions?
My first 6000 was faulty out of the box which they replaced with a new one. I've had the new one for 21 days and probably used it 8 days before it went bad. When i was boxing it up to ship back i heard something rattling inside of it, not good. In researching i found that they've known them to have major issues since March or April, yet they have refused to address the issue with a production stop or at least look at the different production runs and recall those units. I think when it's all said and done there will be a substantial number of them that are faulty worldwide. As it stands now, Detector Center states that there is a" temporary" 10- 14 day time frame for repairing them. My bet is that it's not going to be temporary. If this failure rate continues there may be grounds for a worldwide class action lawsuit, who knows. Oh, and i owned a business for 40 years. Not a very smart way to run a business. JMO.
Just like the college sports transfer portal, I too have decided to change my mind.😁 I was set on buying the new NM Legend. Instead I visited a local MD dealer today and had a chance to test drive the dealers Equinox 800. The Equinox 800 checked every box and then some. It will get me where I want to be in metal detecting. The dealer was pretty impressed on how I was able to navigate through the controllers menus and settings. It is on order and will be here next week. Now for the "goodies" getting thrown in for free. Both editions of Andy Sabisch's Handbooks on the Equinox 600/800, a Minelab Hat (I love hats), and any magazine, current or past editions that are in stock. And there are a lot in stock. Excited is an understatement.
I've had a Gold Bug for 5 or 6 months now. Intermittently when I press the "+" button to increase discrimination it switches into pinpoint mode, will stay there until I release the button and re-press and will then work fine (usually). I've ensured my fat little finger is no where near the pin point button. Been telling myself its likely just some software glitch, annoying, but I can live with it vs. sending it in for repair. Part of me says "get it fixed before the warranty expires stupid". Well cooler weather is here and I will be sending it in.
Just curious if any of you have had the same problem?