Jump to content
Sign in to follow this  
Rajat

Which Is Best Frequency For Detecting Gold Jewelry And Silver Items At The Same Time

Recommended Posts

I always have one question in mind which is the best frequency for silver and gold jwellary or treassure hord at the same time i know 7 to 15 khz is for silver relics tressure 15khz to upper is for gold suppose if i find a cannal full of silver and gold jwellary which frequency is best suited for it 

Share this post


Link to post
Share on other sites

Any one frequency is a compromise. You kind of answered your own question - you want to be somewhere in the middle. Say 14 kHz give or take a little. Very many "do-it-all" detectors run at 12 kHz to 15 kHz for this reason.

George Payne was one of the engineers who patented many of the basic concepts used in VLF detectors to this day. Here is an excerpt from his article at http://jb-ms.com/Baron/payne.htm (2002):
 
"The r component acts differently. It is maximum at one particular frequency and decreases if you go up or down in frequency. We call the special frequency at which the r signal is maximum, the target’s “-3db” frequency. It also turns out that at the -3db frequency the x signal is one-half of its maximum value. This special frequency is unique to each target and is different for different target.

The higher the conductivity of the target the higher will be the targets -3db frequency. Conversely, the lower the conductivity the lower the -3db frequency. The -3db frequency of the high conductivity target will also make the r signal peak at a high frequency, normally well above the operating frequency of the VLF detector. This will make the high conductivity target have lower sensitivity on the VLF detector because the r signal amplitude drops if we are significantly below the -3db frequency. Simply put, maximum sensitivity on a VLF detector would be if we position the operating frequency directly at the target’s -3db frequency. For example, a dime and penny have a -3db frequency of about 2.7KHz. This is where their r signal peaks and would be the best frequency for picking them up using a VLF detector. However, a silver dollar has a -3db frequency of 800Hz. Nickels, on the other hand, have a -3db frequency, where its r peaks, at about 17KHz. Targets like thin rings and fine gold are higher still. Clearly there is no one frequency that is best for all these targets. The best you can do is have an operating frequency that is a compromise."

  • Like 2

Share this post


Link to post
Share on other sites

I think the 8 kHz range is a probably the best mid range frequency for a general purpose, do it all, unit.   Once you start going above that frequency you start to loose the general purpose aspect and begin the road to specialization.   Sure, you can use the higher frequency units as general purpose detectors bu the higher frequencies start to induce inherent bias, which moves them away from a true general purpose detector.  

But as we have seen, the various engineers try to do a general purpose unit with all kinds of frequencies.  But in use, you can tell which ones are and aren't.

HH
Mike

Share this post


Link to post
Share on other sites

If you include gold prospecting as part of the definition of "general purpose" which I do, then 8 kHz won't cut it. If you exclude gold prospecting that's another thing, but is it then truly general purpose?

To me anyway the 14 kHz MXT is kind of the definitive "general purpose" detector by way of that switch in the upper left.....

IMG_1436.PNG

  • Like 1

Share this post


Link to post
Share on other sites

Hi Steve.  I stand by my statement.   I was responding to Rajat's statement of. "I always have one question in mind which is the best frequency for silver and gold jwellary or treassure hord ".    Silver, gold and hoards, while each of which have specialty units available, can be hunted with a good 8 kHz general purpose unit.  And contrary to popular belief, some 8kHz units can make a good prospector.   The Fisher F5 at 7.8 kHz has the hots enough to prospect with and the ground balance circuit is pretty decent.   

The V3i's 7.5 kHz is no slouch either.   The V3i is probably the best around best you have the good 7.5 general purpose frequency along with the availability of the 2.5 and 22.5 specialty frequencies.

Anyway...I've spent a lot of time in that range and it can do most things acceptably.

HH
Mike

 

  • Like 1

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Similar Content

    • By Steve Herschbach
      I have used many metal detectors over the years, and right now I have to say that the new Makro Racer 2 has perhaps the easiest to understand, best laid out, most practical display and menu system I have ever seen in a top end detector. Now, you can sure say you hunt by ear and do not need a screen and I get that, but if we are going to put a screen on a detector, then let's do it right.
      Simple detectors with few functions are easy to make screens for - there is not much you need. But even then just the basics are often wrong. Machines that feature target id numbers, what is the thing you will most look at on screen? The target id numbers! Yet these are often way too small or off to the side as if an afterthought.
      The Makro Racer 2 id numbers are huge, much larger than on the original Racer and Gold Racer, which are already good sized. The number 88 display in the diagram above is fully 1.5" x 1.5" in size in real life. Other machines have some pretty big numbers but I think this sets a record as I can't think of any machine with larger id numbers on screen though some are close.

      Makro Racer 2 LCD display and controls

      Makro Racer 2 screen layout

      Makro Racer 2 screen and control descriptions
      The number can be the ground balance number, target id, or depth reading. You get a text display just above the number confirming which it is. Below the numbers are three zone references, Fe, Gold/Non-FE, and Non-Fe, that are used to set tone breaks and audio for the three main zones or bins as they are sometimes called.
      Another basic feature lacking on a lot of machines - the meter backlight. With the Racer 2 you get off, intermittent, or full time backlighting, and it includes the translucent red control buttons. The control ranges between 0-5 and C1-C5. At 0 level, the keypad and display backlight are off. When set between 1-5, they light up only for a short period of time when a target is detected or while navigating the menu and then it goes off. At C1-C5 levels, the keypad and display will light up constantly. I do not know of anyone doing a better backlight.
      The right side of the meter is informational - ground phase (ground balance number), mineral % (ground magnetite content), coil warning notices, and a six segment battery meter.
      Across the top below the 0 - 99 reference sticker, is a series of 50 "bullets" each of which covers 2 target id numbers. Open bullets (which appear gray in the diagram but are invisible in real life - see top photo) indicate accepted target id numbers. Blacked out segments show what discrimination and notch setting you have programmed in a single quick glance. When a target is detected, the big number on the display will be mirrored by one or more of the bullets flashing dark.
      The four control buttons are simple as can be - up and down takes you through the left hand menu area. Right or left lets you set each function selected by going up and down. The menu is basically the entire feature list just laid out right there for you to see. You want to know what this machine can do, just look at the screen. Most other machines you have no clue without reading the owners manual or at least pushing buttons to see what functions appear.
      Some settings like the backlight are system wide for all modes. All other settings like Gain are independent in each mode, and can be saved independently in each mode. This means you can play neat tricks like setting up a couple modes with dramatically different settings and then flip back and forth easily between two modes for target checking.
      You even get to decide what mode is the default start up mode. The Racer 2 starts up in the last mode where the save function was performed. If you always want to start in Beach mode, just modify and save something in Beach mode. Next time you start the detector, you will be in Beach mode.
      It is simple. It makes sense. No cryptic abbreviations or acronyms. No sub menus. It is, in metal detector terms, a work of art. Whoever designed this should sign it so I can frame it and hang it on my wall.
    • By Steve Herschbach
      First Texas (Bounty Hunter, Fisher, Teknetics) - last new models Fisher F75+ and Teknetics T2+. Next up a new pulse induction (PI) beach detector. A new digital multifrequency to replace the Fisher CZ3D is long overdue but at this rate we will be lucky to just see the PI before the end of the year.

      Garrett - last new model the AT Max. Hard to believe the flagship GTI 2500 has been around since 1999 with no updates. Garrett so far has shown no interest in multifrequency. The most I was hoping for was a lightweight dry land version of the ATX, but so far no sign of that happening either. I doubt we will see anything else from Garrett this year but they could surprise.
      Makro - last new models the Multi Kruzer and Gold Kruzer. Makro has mastered single frequency so everyone would like to see what they can do with multifrequency or pulse induction. I expect Makro is done with new models for the year.
      Minelab - last new models Equinox 600 and 800. I have no idea what’s up next for detectors but I sure would like to see that small coil for my GPZ 7000. I really don’t expect anything new for the rest of the year besides Equinox accessories.
      Nokta - sister company to Makro. Last new detector the Nokta Impact. I actually bet on a PI under the Nokta brand rather than Makro brand simply because the Nokta housings like the new Impact housing would better contain a high power PI.
      Tesoro - Who? What?
      White’s - last new models the MX7 and TDI SL Special Edition plus the just announced Goldmaster 24K. Hopefully that new tech will eventually see the light. Right now just getting the 24K out the door is job one.
      XP - last new products the HF coils for the Deus, with X35 coils due by end of year.
    • By Steve Herschbach
      Our cup runneth over!
      Just a few years ago the market for "over 30 kHz nugget detectors" was quite limited. For a long time there were only a few options:
      Fisher Gold Bug 2 (71 kHz) $764 with one coil
      Minelab Eureka Gold (6.4, 20, & 60 kHz) Discontinued $1049 when new with one coil
      White's GMZ (50 kHz) Discontinued $499 when new with one coil
      White's GMT (48 khz) $729 with one coil
      Things were that way for over a decade. Then in 2015 Makro introduced the Gold Racer (56 kHz) $599 with one coil. Sister company Nokta released the AU Gold Finder (56 kHz) $799 with two coils
      Then in 2017 we see the Minelab Gold Monster 1000 (45 khz) at $799 with two coils. And although not a dedicated nugget detector, the Deus high frequency coil options (up to 80 kHz) were also released, $1520 for complete detector with one HF coil.
      Now in 2018 we get another general purpose machine, the Equinox 800, that can hit 40 khz, $899 with one coil. And just announced...
      the Makro Gold Kruzer (61 kHz) $749 with two coils and
      the White's Goldmaster 24K (48 khz) $749 with two coils
      These last two announcements have made barely a ripple in the prospecting world, or at least going by other forums that seems to be the case. There are various reason for that (forums not being prospecting oriented or being Minelab centric) but still the lack of buzz is interesting. I do believe people are both burned out by all the new introductions and that the market is saturated with high frequency models. Leaving out the general purpose machines to sum up the current options it looks like the current "sweet spot" for pricing is a high frequency model at $749 with two coils.
      Makro Gold Racer 56 kHz - $599 one coil
      White's GMT 48 khz - $729 one coil
      White's Goldmaster 24K 48 kHz - $749 two coils
      Makro Gold Kruzer 61 kHz - $749 two coils
      Fisher Gold Bug 2 71 kHz - $764 one coil
      Minelab Gold Monster 1000 45 kHz - $799 two coils
      Nokta AU Gold Finder 56 kHz - $799 two coils
      High Frequency Gold Nugget Detector Roundup

    • By ☠ Cipher
      Here's another, a second interesting product I've run into recently. This one has a bit of a giggle factor for me, but I could be wrong. See what you think.
       
    • By Mxt Sniper
      Someone has X-rayed a equinox coil. Pretty good sized circuit board inside!
      https://md-hunter.com/minelab-equinox-coil-x-ray-is-it-really-the-half-of-machine/
×