Jump to content
Skate

Where Do You Find Most Of Your Rings?

Recommended Posts

On 2/12/2018 at 10:09 AM, Mike Hillis said:

That is a lot of tabs, Skate.   A lot of large pull tabs.   

Why do you think that you need to be digging square tabs to find a gold ring?    How many types of gold rings are likely to give the same ID as a large square pull tab?   Who would wear a large pull tab type of ring?   What activities would cause someone who wears a large pull tab type of ring to be lost?   Are any of those activities taking place where you dug all those square pull tabs?   Does that activity take place often enough that there is a good chance of a ring being lost, and, most importantly, lost and not recovered?

I'm trying to be helpful.  If you are going to go out and dig pull tabs at least understand why to dig them and where to dig them. 

I cannot over emphasis  the importance of those books titles I posted if you really want to be successful at this.  You hunt gold with your mind and recover it with a metal detector.  

HH

Mike

If I may I'll answer your question from my point of view.  I will dig tabs all day in a park where It can be done without worrying about all the plugs.  It's where the bigger heavier rings come in and one of those can equal 4-5 dinks so, well worth the effort to me.  I'll take large mens bands and heavy 10K class ring any day of the week. I also feel there a lot more of those type lost than say small engagement type rings.

  • Like 1

Share this post


Link to post
Share on other sites

Gold rings are quite hard to find , and they can be found anywhere where people go .

On the beaches look at rock pools , or anywhere they can get trapped . Check black sand areas and below cuttings or ridges in the beach. On the beach the best place is usually just beyond low tide or where i find most of my rings between the tides.

On land they can be at entrances to fields , along pathways , on pasture fields where people have picnics and markets , or in the old days on cultivated fields if a worker or someone lost one . 

And to put salt into the wounds they come in at almost all the numbers people like to ignore , and the best / worst one is the ring pull / pull tab.  

  • Like 2

Share this post


Link to post
Share on other sites

I have found rings in tot lots and athletic fields and even parks.. Tot lots have been good because I have found my gold rings there. Usually the athletic fields I have found silver rings and even a class ring or two. 

I hit one soccer field a few years ago that had 14 fields and took me over a month to hunt at 4 hrs a day but I managed 9 rings and two were gold bands plus $200+ in clad. The rings I found in the playing area and the clad on the sidelines.  Even locally I find 70% of the clad and the few rings I have found were sideline rings at soccer fields, 

I look where people congregate for outdoor events. Festivals and carnivals. Fairgrounds and fringes of ball fields.  Old high school sports fields usually produce well. 

The most expensive ring I ever found was in a tot lot near the kiddie swings. I never miss a chance to hunt a tot lot. More than paid for a detector when I sold it to the pawn shop

If you stop and think about it how often do you lose anything including change from your pocket. That's why newer parks don't produce much they haven't had the years to accumulate coins and rings. 

  • Like 2

Share this post


Link to post
Share on other sites

With Frisbee courses becoming popular this might be a good place to pick up a ring.  Hunt around the Tee box area where they make the initial throw down range at the basket.

  • Like 1

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By Jackpine
      are starting to heat up.  I spent a couple hours at the sand bar this morning and managed a couple pieces.  Nothing to brag about as the stones in the ring are CZ's.   The hoop earring is silver plated.  There were 3 other hunters out and their finds were meager as well with only one gold ring being reported at this spot so far.  
      The wire mesh I had welded in the scoop worked a dream.  The earring back in the pic is just one of many tiny bits it captured saving a lot of time. 😉
      The nut

       
      The heartbreak

      It really felt good to get out and get started on this years "crop"!  👍
    • By Mike Hillis
      Hunting tiny gold jewelry in inland sites is just so different from mainstream detecting methods that unless you do it you don't understand the requirements.    
      #1.   EMI stability.   Your detector has to be stone cold stable.  No spurious noise.  None.  The signals you are after are small tight signals and you can’t hear them if your detector is making spurious noises.
      #2.   The detector needs to be able to keep its HOTs at low gain/sensitivity settings because:
      a... You need to be able to focus on the right depth of signals and those tiny signals are not deep.  Most of the time they are just down in the grass roots.   You want to focus only on the top three to four inches of depth.   If you have to run your sensitivity at or near max all you are doing is masking the desired signal response with reports from all the other signals surrounding it and below it.  And in cases where the ground minerals are high, the ground itself will mask the response.  
      b... You need to control the coil foot print.  In this type of hunting you don’t want coil edge surface responses.  You only want to hear what is directly under your coil.   Concentric coils work better at this than DD coils.  DD coils are ok but you get better footprints with concentric and tighter readings on your meter.
      #3.  The higher the operating frequency, the more important the above become.  As the operating frequency goes up, the level of discrimination goes down because the trash targets hit harder and sound better.   In other words, the higher the operating frequency the better the trash sounds and responds.
      #4.  Notch discrimination or some other form of discrimination that will allow you to focus just on the signal range you are hunting.   The only range of signals you are interested in are in the ferrous/non-ferrous boundary range and the foil range up to maybe the nickel reading.   All other signals are distractions.
      I'm editing to add a number #5.   Tiny signal audio boost is a big plus if it can be deployed while keeping original signal response integrity.  
      I'll close with this.....You can take a gold prospecting unit onto a woodchip playground or a sand pit and as long as it can handle the EMI you can hunt with it on normal settings.  But if you are targeting sites  where good quality, tiny jewelry is most likely to be present, you will be working a lot of turf sites where a prospecting detector's normal feature set isn't going to be very helpful. 
      HH
      Mike
    • By Randy Dee
      This post is mainly directed to UK field detecting where we have had social open air gatherings since Medieval times and on fields littered with coke. I used these settings yesterday and I was hopeful of finding at least one gold necklace / chain but alas none, better luck next time.
      As most of us know it is almost impossible to find a fine gold chain with any metal detector and as it is a long story why but mainly due to Eddy Currents and the metal detector rejecting coke which fits into the same frequency range as thin and fine gold and as here in the UK we find our permission fields littered with coke which mostly emanates from the days of steam engines powering farm equipment and the spreading of night soil as a crop fertilizer and which was collected from house middens and where the ashes from the household coal fires was used to cover the stinking human excrement, these ashes contained large cinders which survive for donkeys years in the soil and give off wonderful signals for metal detectors.
      This information on how to adjust the Tone Breaks to enhance the chances of finding gold chains during field detecting is only applicable to the Minelab Equinox 800 as it has the advanced settings capability.
      To alter the "Tone Breaks" it involves making changes to three "Target Tone Dependencies" which are "Number Of Target Tones", "Target Pitch" & "Target Volume".
      Here is my effort to change the settings to cover the frequency conductive range to give off a signal from thin gold chains in the discrimination zones, at present the default Discrimination zone is -9 to +2 and it is the Zero to +2 segment where gold chains show.
      So first of all select either "Field 1 or 2" your choice.
      Then go to "Target Tone" choose 5 tones.
      Then go to "Tone Breaks" and set the 5 tones as thus T1 = -9 to 0, T2 = 1 to 2, T3 = 3 to 28, T4 = 29 to 38, T5 = 39 to 40.
      Then go back to "Tone Volume" and set tone segments to T1 = 1, T2 = 15, T3 = 25, T4 = 25, T5 = 15.
      Then go to "Tone Pitch" and set the tone segments to T1 = 1, T2 = 15, T3 = 25, T4 = 20, T5 = 16.
      To move from from one tone segment to the next segment use the "Accept / Reject" button ( \//x ). These settings are working for me but then again they may not be every-bodies cup of tea.  
    • By schoolofhardNox
      Well today was beach hunt #7 with the Equinox. There wasn’t a lot of detecting room, with the way the tide was today. Also, a lot of people walking and laying out on the beach. It’s getting crowded out there. I was hoping to keep the streak alive today and I didn’t have to wait very long. First good target was the pink stone 14 K Gold ring. I almost didn’t believe it. That made the rest of the hunt less stressful and more enjoyable, as the gold streak would continue. But I didn’t expect to get too much more, but the finds kept coming.  All the time I just kept shaking my head, I can’t believe what Minelab has done!!! 4 gold rings, some silver and a small amount of clad. The broken class ring was found in 2 separate holes about 60 ft apart. The breaking points match up perfectly…they were part of the same ring. The tiny targets were out in full force, as well as the pull tabs too. A small price to pay for the good finds that can come with it. Probably the smallest chain this machine can pick up. Had a hard time locating it once it was out of the hole. I was glad to get out today… a picture-perfect weather day!






    • By Mike Hillis
      Patch Gold = A patch is a hot spot with the right ingredients (cover, clientele, and activity) to allow re-occurring jewelry losses over time.  Patch Gold is gold jewelry found in this hot spot.   
      This is nice piece of Patch Gold from one of my patches.   18k White gold with a very pretty diamond I found a few weeks back.   
      HH
      Mike
       
       
       

    • By mn90403
      I went out early this morning.  I was expecting a cut as there had been a 3 hour period of high waves during high tide.  As it turned out it was more of a 'blow over' than a cut so after about an hour it was time to move.  My next beach was less blown over so I settled in for a bit.  Finally I found a few quarters and that can mean rings!  So it was today.  My first ring was the 18.  This made me circle, grid and look near for another.  About 20 feet away I got the 16.  Nice 2 ring morning before 7 AM.  I kept hunting and found the cheap tennis bracelet and then I got the 8, the 3rd ring.
      I'll give the composition of the ring and you tell me which number goes with it.  I'll come .back Thursday Night and tell you the number that goes with the ring
      There is a copper ring in the top center.  There is a silver .925 ring on the left with a nice little amethyst.  There is 18k GP ring with a larger glass or crystal on the right.
      Mitchel


×