Jump to content

Recommended Posts


But I thought the Equinox was a game changer, not a head turner!

 

Share this post


Link to post
Share on other sites

.... multi frequency works very well ....

  • Haha 1

Share this post


Link to post
Share on other sites

In my case it would be the V3i. I rejected and sold the Deus as not for me a while back. I just think that there's something about multifrequency that no single frequency machine can compete with, even if there are many individual to pick from. Minelab has a winner here that has balanced out that FBS preference for deep silver, while overlooking small gold. I've always been tempted by the CTX-3030 too, almost solely for the pinpoint target trace feature. I hope Minelab builds on this kind of imaging in the future. Absent that, the even the mighty CTX is hard pressed to do much of anything it's sparky little brother can't. 

  • Like 2

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By cjc
      18/ How to Run “10 kHz” as a Cap / Iron Identifier
      A lower frequency like “10 kHz” is what can be called a “plodder.”  It responds slowly, makes sure its reporting accurately and only shows a couple of numbers to describe what it sees.  When you run “10 kHz,” make sure to give it the time it needs to do the task.  Switch over, wait for the threshold to return and make a slow, even coil pass.  Just as with “Multi” the first numbers that appear may be cap or gold-range indications--in the teens.  However, when you go to the cross sweep (or even a slight angle) the ground becomes apparent in the forum of a  ”20 plus” reading. This change will be a lot more definite than with “Multi.”  So go slow to let the slower frequency process, use the cross sweep and watch for the “wild” high number indicating a cap or iron.  “10 kHz” produces a more defined, more “general” meter response.  This response takes into account more of the ground’s signal--making “10 kHz” a great cap identifier. (This is also a great illustration of the dichotomy between what the high and low frequencies actually do).
      The idea though is to work on your coil and meter recognition skills so that having to make the change-over is a last resort for only those caps that display a very narrow band of numbers in “Multi.”  These are in the minority.  I especially go to “10 kHz” where the indication shows “14”--again--a good gold number.  
      (Note: If you are using the 800, in “5 Tone” a high “Tone Break” of around “19” or “20” will produce an intermittent high tone on caps with this test.
      Another interesting lesson to be observed when running “10 kHz” is that if you make multiple passes of a target sometimes the slowed response speed will cause the meter response to “double up”--that is it gives a “cumulative” high number.  This is something to watch for in that a response can be falsely “ID’ed” as higher than it is--in this case a worse signal.  Referring back to our “coil control pass types” above, this kind of a response comes from making “keep in” passes--instead of letting the target leave the detection field each swing (so as to “reset” the meter).  Both have value in identifying responses but it’s good to be aware of the difference. 
      It’s important to recognise the parallels between this machine and the CTX.  With the CTX this “grounded” number comes in the form of a “1” or “30” “off screen” response--indicating iron or steel (non-constancy).  I’ve heard these referred to as “cross-feeds” In that they initially sound good as the two parts of the response “connect” on the first pass--but this electrical “join” is then rapidly processed out with subsequent coil passes.
      With the Equinox these indications are more centered on the meter--"10” for rusted caps or “20” plus for steel caps.  It’s more like where you have a coin next to iron--pulling the response down (or up towards the “wrap” zone).  With an analog detector--either of these (CTX or Equinox “outlying” numbers) would be the low tone (or “nulls)” of iron mixed in to the audio response, or a high “sound off” or “false.” 
       From: "The Minelab Equinox: An Advanced Guide" (2018)
    • By Steve Herschbach
      without the 80 gram scuff cover and 660 grams with scuff cover. The 11" coil weighs 524 grams with scuff cover. Added weight to front of Equinox 136 grams or 4.86 ounces. Equinox total weight with 15" coil 3.26 lbs.
      The CTX 17” x 13.5” coil weighs 901.5 grams / 31.8 oz with scuff cover.

      Minelab Equinox 12" x 15" DD coil

    • By Tnsharpshooter
      Put this together this morning for folks.
      Btw hot program used on Deus version 5.2,TX power remained at level 2.
      Equinox using Park 2sensitivity  24.
       
    • By Tnsharpshooter
      These experiments done over medium mineralized soil.
       
    • By Mark Gillespie
      Well I can say for sure the wireless headphones that come with the 800 model are the best I've found so far.  I've been experimenting with different wireless brands of headphones and I've yet to find a single pair that comes close to the performance and minimal lag time compared to the stock phones.  Amazing machine.
      Congrats Minelab.

      Minelab Bluetooth / Apt-X Low Latency Wireless Headphones for Equinox 3011-0370
×