Jump to content

Reviewing Tony Eisenhower's Headphones For The Equinox

Recommended Posts

On 3/26/2019 at 12:21 AM, sjmpainter said:

Did you get a chance to try out the headphones? Any thoughts on them? I have a pair of Grey Ghost but they are really quite in the water looking for something better myself.

I have not used them underwater but in a casual air test the Tony Eisenhower headphones are definitely louder than the Minelab yellow underwater phones.

Link to post
Share on other sites

M/L, Harolds (with a jumper from CTX), GG 
Amphibians (not terrible) and TE's (best).


  • Like 2
Link to post
Share on other sites
  • 1 year later...

I’ve had a pair of Tony’s headphones since last summer. I use them with my Tarsacci. Great quality, great fit and the sound is good too. Their holding up very well, no problems!



  • Like 1
Link to post
Share on other sites

I have a pair for the Nox I use in waist deep water, my only complaint is wind noise. I have a pair of Nokta waterproof phones for the Simplex that seem to be louder and less prone to wind noise.  I'm sure if I used Tony's underwater the volume would be adequate.  The build quality is great on Tony's compared to the Nokta's.


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Content

    • By F350Platinum
      Hey y'all,
      The last couple of days I've been out bashing the farm with my new Equinox 600 instead of my ACE 400. First day I went through my yard again, and was surprised I didn't find anything new save for one button where I first started using the ACE.
      Yesterday and today I searched the farm where I've been scoring a lot of 1700's stuff, but it has sort of dried up as I've gone inland. Found a nice 1917 buffalo nickel, and a 1981 memorial, but mostly beer cans and buckshot. Think I may have found part of a lead token.
      I also went over to one of the other fields to see if I could locate where a house used to be in the 1800s. Really trashy area! I dug everything and found some brick so I knew that I was in the right place. However, I noticed the detector tends to make local dogs bark, and most around here are untied.
      A few days ago I thought of what I could do to prevent this problem, but still hear while detecting, particularly now it is hunting season. Might save a life! I remember researching headphones a long time ago, and ran across a certain type of wireless headphone - Bone Conduction. Last week I was able to find a pair that were Aptx Low Latency, perfect for the Equinox, and the only ones out there with this particular protocol that I could find. Others mention BT 5.0 but not Aptx LL. They're not waterproof but they are comfortable and pair easily. Here is a link: https://www.amazon.com/Avantree-Bluetooth-Conduction-Headphones-Housework/dp/B07Y1J7RZT/ref=mp_s_a_1_11?dchild=1&keywords=avantree+aptx+bone+conduction&qid=1609205776
      Sorry, Amazon links are long sometimes. They're $59, and they work great. Of course they came after 5 today, so I was running around in the front yard after dark...

    • By mn90403
      Will these work with the Equinox?
    • By Matelot
      Hi all.
      Over the last couple of days I've had a complete nightmare trying to pair my ML80 headphones to my Nox 800. So much so that yesterday I had to detect just using the speaker. Had a fairly good day though so it wasn't all bad! Anyway I didn't want to resurrect the two and a half year old thread below and thought I'd post a solution I found today whilst trying to get the damn things to connect.
      So, after trying all the solutions in the thread below, reading the manual, factory resetting everything and watching various Youtube vids I still couldn't get them to connect to the detector. Now my headphones WOULD connect to my iPhone so it wasnt a problem with them.  In the end I tried to connect the WM08 wireless module to the detector, which worked so it wasn't a problem with the detectors bluetooth card. Now I was pulling my hair out! Anyway I tried connecting the headphones again after the success with the WM08 module and bugger me if they didn't connect within five seconds! I've confirm tested that they will connect automatically going forward so all is well. There doesn't seem to be any logic to that solution but it worked. So if anyone has an issue in the future and nothing else works, try connecting the WM08 module first then trying the headphones again. Well, guess I now have to go and redo all my detector settings. Cheers all. 
    • By zippykar
      Newbie here,how do I connect the  Garrett Z-Lynk to the Equinox 600?  Doesn't the WT-1 box of the Z Lynk have to be physically connected to the 600 via adapter cord? I didn't see any such cord on the Minelab site.
      I just bought this 600 havn't even used it yet  but fter reading post from different sources, I think I'm going to hate this thing.
    • By Steve Herschbach
      These are available at some dealers now. Headphone Adaptor Cable 3.5mm (1/8-inch) to 6.35mm (1/4-inch) Part No. 3011-0369 $40.00

      Minelab Equinox 1/8" male waterproof connection to 1/4" female non-waterproof connection
      I plan on wading a lot with the Equinox and this creates a waterproof connection to the detector itself. The cable is two feet long and reaches just about to my shoulder. Main gripe - the straight connection once it makes that 180 degree bend gives up some length. To prevent stress from pulling on this constantly the cable should be affixed to the detector itself so the cable does not get stressed repeatedly where it makes the bend.
      This is a good solution for people who want to hunt in the water but do not need to put their head in the water, and so who do not need the waterproof headphones. The cable also mates directly to the WM08 module for those who wish to use it for that purpose.
      Minelab Equinox Parts & Accessories Page
      Do be aware there is a compatibility issue as regards the Equinox external speaker. If headphones and adapters are not wired correctly the speaker will keep going even with headphones plugged in. Here is the Minelab article on the subject. As far as I know this applies to the CTX 3030, GPZ 7000, Gold Monster 1000, and both Equinox models. I use Sun Ray Pro Gold (CTX version) headphones which are wired to work properly with the Minelab units.

      Minelab headphone wiring diagram
    • By GB_Amateur
      Is there now marketed or has there ever been available a detector which inverts the audio volume scale?  Many applications produce better finds from the weaker signals, either because those items are smaller (e.g. micro jewelry) or deeper (e.g. old coins and nuggets).  Having to listen through the din of trash to hear the weak signals for most detectors is mentally fatiguing.  I wouldn't be surprised if this is/was possible with analog electronics, but seems like a task that digital processing could handle easily(?).
  • Create New...