Jump to content
  • ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

    • By Norvic
      Well, my Son did it and turned up with a SDC in exchange for my 5000 for Easter. Went off to try the SDC, left him with Z to compare with 5000 and new age coils, he was fairly impressed with performance of 5000 with the Elite 14" but in using the Z to compare he is now spoilt and talking Z Z Z Z only. Suspect the 5000 is history, regardless that the new age coils have increased the performance of the 5000, the stability of the Z has swung him.
      The SDC, it is super stable and a small piece magnet, good fun and will complement the Z. It is the small coil gold detector for those pieces around boulders the Z just can`t get at, plus for those shallow pieces that recovering is time consuming for the Z.
    • By Walker
      Yesterday I beat my old record. Now it's .023 gram. .35 grain. I don't know if that's a good thing.
    • By spencer@wy
      So i got a little cuious abt my f3 and ability to adapt to other coils and took her apart. the coil plug in is a smaller 6 pin unit. 5 wires attach at coil adapter;blk,red,yel,blu, and green. Circuit bd tentitavly look like blk n red are tied as well as yel, blu, and grn.
      coil has 29 turns with a little steel/non copper wire soliered to the leading/starting end of loop. the ANTENNA as i call it, is aprox. 10" length, starts at soldier conn near coil cntr goes 6 oclock to wrap around insulated portion of coiled wire where it enters coil pltfrm. then it goes to abt 10 oclock position bout half distance between cntr and edge of coil, passes from top side of spool to bottom side of spool where it then turns right angle to upper run and terminates bout half distance from coil cntr at aprox 2 oclock bearing from cntr.
      the spool is styrofoam 3/4 thick w/ spool groove being 5/16 " wide or tall, and in-set abt 1/2 " it is held in place by rubber band and entire surface of spool is wrapped with heavy paper that appears to have graphite? looking coating on it.
      Just my preliminary findings, for those curious.
      now i just need: info on winding coils, findd small 6 pin plug-ins, and a 3d printeer to make coil foot adapter to hold other coils.
      thats it for now, gotta do some home-work on it. I ll post more later. Happy hunting.
    • By bado1
      Are stable threshold settings on the sdc (1,2,3...etc.) dependent more on ground conditions than anything else? The reason I ask is I have not been able to run the threshold on my sdc less than #3. On 1 and 2 the threshold is intermittent and "warbely" and basically un-huntable . On 3 she's stable and I'm finding the tiniest bits of gold. Iv'e hunted various locations here in Central Arizona and always have to set it to #3 to get a stable threshold that is not intermittent. Normal?
    • By Rick Kempf
      An interesting thread on an OZ forum on interchanging coils.
      Lots of back and forth, some misinformation - the Ismael - a long tome modifier of ML PI machines, chimes in and says - "no problem"!
    • By rc62burke
      Hi All
      Ever since I purchased my SDC I have been wanting to make it a wireless unit as I enjoy the freedom of no cables on my SD2200d by using a "Little Ripper" system.
      So with numerous questions on forums & checking out anything along these lines, I finally found some info online, so armed with a bit of info I went down to "Jaycar" & hey presto they had what I needed.
      I purchased 1x "Bluetooth Transmitter (which can receive also) & 1x "Bluetooth receiver, an adapter plug & adapter lead.

      I connected it up yesterday when I got home & gave it a test run & it works great!!!!!!!!!!!!!!!! "Very Happy" ATM I use under-chin ear-buds but my next mission is to set up a booster with dual speakers.
      Here is a few pics of the parts I bought, the larger item is the Transmitter, they are USB chargeable with 8 to 6 hrs run time.

  • Create New...