Jump to content
Sign in to follow this  
jinmon

Frosted Rocks - Mmmm!

Recommended Posts

Saw some neato rocks in the Cajon Pass Area by the train tracks. I suspect this is a byproduct of the railroad somehow but wasn’t sure what they could be so I figured I’d share and someone smart would recognize it!

As you can see, the first rock is chocolate-glazed. The third pic is of a clear sugar-glazed rock  - much harder to see the glaze because it’s clear, just take my word for it. 

What could’ve caused this? I suspect heat was involved but past that I’m clueless. 😁 Thanks in advance!

38C4C4FA-7B47-45EB-8287-ACB317576171.jpeg

328E967A-5C77-49C5-A389-BA8FC6B005A7.jpeg

6E47C34B-B0C4-4DF6-A0F2-8C2C26A973F6.jpeg

  • Like 2

Share this post


Link to post
Share on other sites

Looks like slag from a smelter. Not uncommon near railroad tracks transporting material to and from smelting operations.

  • Like 4

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Similar Content

    • By Tnsharpshooter
      https://metaldetectingforum.com/showthread.php?p=3118425#post3118425
    • By phrunt
      I was looking around the new Minelab website and I noticed they now say the Equinox is single frequency on Gold Modes, is this some sort of error or are new Equinox 800's coming without multi-IQ on their gold modes?  I found nothing wrong with MultiIQ Gold modes so I don't see why they'd change it.
      https://www.minelab.com/metal-detectors/equinox-800
      Detect Modes
      Equally adaptable for all target types and ground conditions:
      Park Field Beach Gold: Gold Mode operates the high single frequencies of either 20 kHz or 40 kHz to detect gold nuggets in mineralised soils.  
       
    • By dan_h
      Used Cherry Pick settings from the Handbook for  a brief session in a local park.  Found a penny, the handle of a spoon.  If it ever was silver plated, that is long gone.  Then found a quarter-sized disk, a token of some sort.  It says "Where a kid can be a kid" on both sides and one side was stamped OTTS.ORG.  I  just tried that website and it is apparently closed.  There was a message to the effect to leave your contact info if you have any business with this site.
       
      Question:  is there something more than the Lesche Predator but less than a shovel -- a mini shovel, perhaps?
    • By phrunt
      What are peoples thoughts on Ferrite Choke's/Core Filters on coil cables?
      I noticed that with my QED detector a Ferrite Filter came with it to clip onto my coil right up the end where it plugs into the control box.  As I have a few coils I clipped one on each of them as I had a few of them laying around, I was a couple short so I'll have to buy some more to do every coil. 
      Seeing the QED uses them I was wondering why other detectors don't so I googled images of coils, Well it turns out they do...

      Above is a picture of a CTX 3030 coil, note at the end where the cable plugs into the detector is the Ferrite.
      And then the GPZ 7000 also has one, but Minelab did it the better way by putting it on the wires inside the control box.  This method would work better as the wires there aren't already shielded so the ferrite can work its magic better.

      Above is the Wiring Loom, C-Box Coil Connector for the GPZ.   This is the perfect method in my opinion, the wires loop around the ferrite to give the best results and there is a shield wire going down onto the connector.  This could possibly be a method the QED could use in future upgrades to give the best results as putting it over an already shielded wire would limit its effectiveness I would think.
      The filters probably do a better job at helping prevent EMI out of the detector than coming into it, but it would be interesting to know peoples thoughts on them.
      I'm going to order a few more clip on ones to put on my coils I use on the QED anyway as it must need them, these are the ones I'll get, simple clip ons...  5 for $2 🙂

       
       
    • By Meikle
      My detector has been having some problems lately. I have a teknetics liberator. The other night it was chirping periodically. In the morning it wouldn’t turn on. So I checked the connecting points and put a fresh battery in and the power button still didn’t work. When I put the battery in it would turn on automatically but then would turn off after a short time.
      Has anyone ever had experiences fixing this?
    • By WesM
      Say I'm trout fishing today and find a 4" quartz seam loaded with visible gold (Googly 'gold in quartz and it's as good as anything on page 1). But, the land is already claimed by an armchair 'miner' that actually just uses it as loooong term camping/fishing/hunting space without campground antics and charges plus it's close to a deer layover area. Say I know this for sure since I met his grandkids and son years ago during hunting season and taught them how to snipe for gold on that very stream since the 'miner' was oblivious as to how.
      What would you do;
      Tell him?
      Wait for him to lapse his claim into abandonment or die?
       
       
       
       
       
×
×
  • Create New...