Im brand new to detecting and have the Nox 800. I thought id do a test bed and search around home first before going out...Im having a issue trying to figure out what is what...I have a VID numbers list but not sure i see galvanized nails, bolts washers etc... My readings are all over the place...so just started digging up yard 😂. Tons of stainless steel nails (For siding i assume) as well..when i go over these targets in park 2, 15hz and multi i get readings of 24-30and they also jump all over...so I go into all metal mode...Then changes to mostly less than 0 #s as well the higher numbers...Ive also have gone 90 deg to targets as well and get same reading. So getting a bit frustrating... I have threshold at 0, sensitivity at 20 or less, 2 breaks less than 0 for ferrous (volume at lowest setting) and then above 0 for non ferrous, recovery speed at 2 ....is there just too much trash and am i better just to go to a park to learn? there also seems to be a lot of black sands and small pebbles that are magnetized as well as a magnet picked up a lot..and my pinpointer was going off like crazy and i couldn't even find the target I know Im all over place here but a little guidance would be much appreciated! thanks!
By Steve Herschbach
Since this is an Equinox forum, people may assume it is supposed to be all sunshine and roses. The truth is I love well written critical commentary. The problem with most negative posts about detectors is they come down to "I saw a video somebody posted and that machine sucks". Personally, I see minimal value in that sort of thing.
What I want to see here is posts and reviews from people who A. have actually run the detector and B. can offer straight up critique without the extraneous "boy, how dumb can they be" commentary. What do you like, what did you not like. What worked well, what does not work well, and why. Things to do, things to avoid. Whatever. It's not that you have to heap praise - if you don't like something for some reason then simply explain why.
Here is the first review I did on a Nokta product. Notice I mentioned several things about the machine I was not wild about. I did not beat the company up for it - just stated the facts as seen from my perspective. Notice I went back later and also commended the company for later addressing those very issues.
Where is my similar review as regards Equinox? Can't do it until I have an actual production unit in my hands or assurance that what I have would match a production unit in every way. When the time comes I will do my thing, though it will not need quite the detail of the Nokta review just because so much of that stuff has been covered already here on the forum.
Just wanted to get that out there. It is probably premature so I will bump this up again when units start shipping. All we want to know, all of us, is what people around the world think about various aspects. Some things will be great, some ok, and a few not ok. That's real, and real is all I ask for. Thanks!
I have a eqinox 600,where i live is a 1700s site.been detecting it for 20 years with a number of high end machines,also buddies of mine detecting it,year before last pulled out 13 large cents with my atpro.just a little side note atpro not used in pro mode is useless,in pro mode its awesome totally different machine. but back to why im posting,everything im detecting is mostly in the teens,strong signal ,rotate around the target, still a strong signal,dig rusty nail.everytime.i have iron bias at 3. most targets are going to be below 13 inches that is where my atpro massed out.so my question is why the teen vdi numbers for iron and is there a way to get past the 13 inch mark. sidenote, the house I live was George washingtons surgeon during the revolutionary war. any help is greatly appreciated.
Looking for tips on detecting tailing piles...
I have the Equinox 800 and the Minelab 5000.
and a lot of trashy tailing piles to detect !!! 🤠
BTW----- Looks like we are running low on masks 😷 and gowns here in LA--- but we will survive--
Vets have been exposed to tougher stuff than this!!!
Social distancing does not have to be social--------- but it should be physical-!!!----
I cant see why most of you would have to learn how to do that-???
-- you been practicing it with me for years🤣🤣
Carry on and thanks for any tips on the tailing piles..