Carolina

If you circle the target and get that double blip, keep on walking. Solid hit 360 degrees dig it up. That will cut out most of the tent stakes.

If you connect to your scope, set the delay at anything but 7uS, say 11, then turn of the machine and back on again without moving the delay, you will gain some knowledge most don’t have. Use any mode you prefer. If your working ankle deep, then you should swing your coil parallel to the water or north to south. East to west will continually try and balance the depth and salt difference resulting in noise. A good starting point in all metal I think would be volume 8>10 sensitivity 4>5 threshold 4>5 (your preference) ATS 6>8 reject plays no part in all metal. Tone mode volume 8>10 sensitivity 4>5 threshold 4>5 ( again your preference ) ATS 8>81/4 reject 3. Keep your wet fingers off the coil connector as much as possible. The metal locknut develops capacitance due to no shielding in the Souriau connector. I prefer tone mode mid summer looking for fresh drops. No coins for me. Any iron grunts deep in the wash by the rim I dig as that is where those big fat pig rings lay. Otherwise I keep moving looking for gold. Good luck to you.

I do know that they run at different pulse rates. All metal and tone run different pulse rates from one another and from mute and volcanic. Contrary to the manual mute and volcanic share the same pulse rate. I have no knowledge of any kHz other than the resonant frequency of the coil which remains the same in all modes. Good luck everybody.

If you click on where it says visit the Fisher Store, it takes you to audio equipment and a Fisher emblem I’ve never seen. Wild.

I have no idea. I wish Carl would chime in. I know Dennis put his in that Pelican box or similar box. I however don’t have any photos of it or any idea how it was done. I would think FT would offer a fix for a reasonable price. Here is another machine I had replaced because of shoddy workmanship. You can see some type of sealant if you zoom the photo.

One of my first suggestions was to change the way the control box is mounted or at least the material used to mount it from hard plastic to nylon or SS. It is hard to explain but only a rectangular piece of plastic the shape of a domino but half its size holds the control box to the handle via two screws. Below are a few pictures of LE Jags ( look closely at the yellow tape ) and then my first AQ which had a fight with a breaking Atlantic Ocean wave only a few days after I received it. It will rock left to right on the handle as it is a poor mounting design. If you notice, now LE Jag has his mounted in a Pelican box and carries around his waist.

Small 14k chain, 6 grams (27). Crayon in picture for size comparison of targets.

I think everyone should go back and click the link F350Platinum posted.

Seems like you could go back through each post and add it up.

That piece is the wave. I ordered another antenna for my second shaft and it came with it. If memory serves me $33.

Cliff you run tracking on ?

Thank you chase. I did not even see the button! I got to start wearing my glasses! My first update showed O.6 to the immediate left of V 0.71. Thanks again for your help. As I stated earlier I will not be rolling back.

I’m a unlucky ducky. Not that I would roll back as V 0.71 seems fine to me but my update does not give me the option to roll back.

I hunt 95% in water so I use a strap. My CF shaft has a Steve Yerky cuff pad and the Deus has a “spiffy” XP cuff pad. The straps exit the top of the pad but the cuff slots are on the side.

Well this is what I see now.

I got the Ukraine cover and it is a bear to install with an arm strap.

11.5 on the AQ scale is actually 15 uS delay. It was changed at the last min. and all the face plate labels had already been printed. Just for those who do not know.

Well dang. I will pull up the update again tomorrow. My friend saw the screen same as me. Strange. Thanks for the heads up.

Are you near Perugia by chance?

I haven’t seen any video on V0.71. I also have seen no reports. One thing I noticed, when it first was available it gave you an opportunity to go back to V0.6. I did my friends the other day and it no longer offered going back to V 0.6.

Hi Dew, wish you much luck. 60 month warranty vs 18 months, depth rating much deeper than I will ever go vs 1 meter 30 mins and updateable, many different programs and tone selections and much more for basically the same price. One thing about Dimitar, he certainly is number one for customer service and satisfaction of all manufacturers out there. Watch your buddy Cliff.

I assume Deep HC ?

They are clearly listed in the manual along with frequencies used.

I have two unanswered emails as well. What’s up with that ?

I love my Deus ll but $1600.00 and it comes to this! Deus needs to figure this out quickly. Glad your up and running again.