CaliGold

999$ obo shipped UPS from Santa Ynez. gotten NO offers. zzzzz pat

I love in your bio where it says "whites tdi sl, they might be tweaked a little" lol

950 +/- shipped from Santa Barbara County. OBO obviously... 750 without extra coils. Haven't gotten an offer yet. WE SHALL SEE. I have a sdc2300 Mine Lab in route to me too. This was a great detector, I just need something more sophisticated with LESS settings for small gold and waterproof. I'm a river rat so this thing has to be babied near rivers. Note, it has never been swimming... The waterproof and basically one knob Minelab is up my alley... Trying to sell/ship before I leave town Sat for Colorado. Reasonable offers will be entertained. I take paypal and will ship immediately. There's a ups store up the road here in Santa Ynez. Pat

I have a 2015/2016 whites TDI SL tan edition for sale. It has been used seldom to in-frequently and VERY little in the past 2 years. Almost less than 5 times. I did some mods to it and it works great. (thanks to the community here for the coaching) You can see mods in my posts. I have a 14" coiltek tdi series coil, a Nugget Finder Sadie Coil sika flexed for waterproofing (tested 3 times then hunted once in East Fork river works fantastic) bought a few months ago, the stock Miner John 8x12" coil, and a modded panasonic 16v battery pack and the regular AA batter pack. I used the stock nimh rechargeable battery pack to make the current Panasonic 16v pack. I have the stock charger base (lost the cord/adapter). The detector has lots of gain increasing mods and includes a "boost switch" to control a bypass on a removed resistor. I've tested it a bunch since all mods were completed and it works awesome. I will note that the 14" coiltek tdi series coil should be used with the lower voltage battery AA stock pack. I suppose you could make a 3cell- 18650 Panasonic pack for that coil if you must have it. I'm getting a minelab from up north since I was trying to turn this puppy into a minelab. Not Happening... I'll add some pics when I can. Let's hear some offers..... *Full Package -$950 OBO shipped. *Without coiltek and NF sadie coil and includes only the Miner John 8x12" coil (great coil) -$700 plus shipping Either package includes: 18650 battery charger for the panasonic batteries and an orange Nokta 2019 Pinpointer (runs on 9v). Thanks Patrick email for more pics info to talk etc. patrick@patrickwprice.com

@Jim in Idaho @PI-Man @Melano87 Alright gentlemen... Went up to San Gabriel River East Fork this week. Took the TDI SL for testing and to see the condition of the riverbed after all the rain this past year. Haven't been there in a while as its usually packed with tourists in the summer and the water level has been high since we got lot snow/rain in the winter/spring too. The TDI was great. Found bird shot in bedrock crevices like nobodies business... The side of coil sensitivity is very good. Chiseled chunk off where BB was down an inch or so in behind the slab (sorry no photos), so this was a good "gold scenario" test for areas where the bedrock type and river flood stage are more conducive for nugget hunting. Anyone who has been to this area knows metal detecting is usually fruitless near the river downstream from the Bridge To Nowhere (5 mile hike from parking lot) or unless you're up on a bench. There was heavy helicopter activity that day so the bench I had planned on scouring was, lets say, "occupied" with powerline maintenance and Helis... Is what it is. There is simply too much trash in the stretch of river adjacent my originally planned bench to detect unless you are game to dig lets say 5,000 targets in a day... (nope)... This is a known sluicing dominated river and crevicing/detecting WAY upstream somewhat... At any rate, after finding tons of trash and several birdshots, and a 1975 nickel at the old Eldoradoville town site, I took to the stream bed to sample some virgin 2023 flood gravel. I classified some nice average fist size Jenga gravel (literally off the top of the ground) to about 3-4 gallons of 1/4" to 1/2" material and panned it out slowly. Got some fine gold, amalgum, to at least say I didn't get skunked... I also got to test out my satellite messenger (Zoleo) which worked great even in the canyon, or when driving and device on dashboard. I HIGHLY recommend anyone prospecting out of cell range to get one of the many options for these types of devices. After I'd say 2-3 hours of on/off detecting before starting my pan sampling, the detector still sits at 70% battery. I'm happy with the mods and excited to hunt down some nuggets upstream or in a better river up North, and more importantly glad I got out for some river time, fresh air, and a good 8 hours of moutain ops helicopter viewing. Only my second trip out all year... My profile pic and banner was last trip to Tuolomne county couple months ago for some panning. Much larger gold there to be had. Pickers a plenty in the motherlode... (You can see in red circle the patch of gravel I sampled. I'll definitely sluice this spot if the gravel is still there next time up). A lot of guys go upstream, so with the rain this year, I think downstream is a little nicer than usual. ) -pat

@Jim in Idaho @Melano87 @PI-Man I took the plunge and removed R86 resistor and made the sweep speed mod yesterday with some gucci $ caps I found on digikey to spec recommended. Machine seems ok in air tests. List of Mods: -Q4 mosfet "beefed up" and heat sink added. -R9 & R14 resistors wattage increased 2 watt on R9 and 3 watt on R14. (3 watt much thicker but fits fine 2512 size footprint) -C42 Jumper and on/off switch installed and mounted on control panel exterior. -Sweep speed Mod (C20 and C21 capacitors swapped). Digikey part #s SMR5224J50J02L16.5CBULK 399-13054-ND -R86 resistor removed (near gain plug) (easiest "MOD" to complete lol) -16.64V battery pack (my charger wont go past 4.16 on each 18650 battery) -I have waterproofed my 8x6 Sadie coil from Nugget Finder with Sikaflex 221. (hard to find other than amazon or an RV repair shop... I find the machine runs great with gain up around 50%-80% and with Gain Boost switched on from c42 around 50%. God have mercy and bless this machine to find much Gold. Thank you, again, gentlemen. I hope I don't let you down. Patrick

Thanks Karl! @Jim in Idaho what do yo think of this idea Jim? Karl is the guru obviously but has anyone got any anecdotal info on this? @Melano87 know anyone who did that- removed R86? Very tempted to remove R86 and still on fence with swing speed mod. I waived a .15gram (about just shy of 2 grains) test gold flake in front of sadie coil fast today and it got good decent signal at 2 inches so maybe unnecessary? Does gain increase depth or is that only possible by current from battery etc? (man I want to use that 20v battery again) Terrified though... Maybe if I swap out R9 and R14 current 2 watt resistors for 3 watt (I just got some) The Q4 installed with heat sink is already a higher rated voltage model with some different specs here and there that as a lamen I read to be an "upgrade". Looking forward to the days when my posts on here are the "look at all this Gold I found with my modded out SL" sort... Many thanks, gentlemen.

@Geotech anyone here know about removing R86 resistor down by the gain control area? Saw online... Is that flying too close to the sun? Thanks! p.s. thanks again on the schematic etc. Switch on c42 went well... works good. -Pat

Thanks for the thread link. Interesting. So upon testing the new c42 jumper switch I installed, I found the increase on signals to be pretty intense. It makes the machine run a little hot but maybe that was just the sun and the 16v battery I was using. The gravel in the river bed I test in is pretty intensely mineralized. I guess thats why the wine around here is so good. 😉 Noise goes up a bit with switch on but I slowly learned how to harness the extra gain. It's a nice option to have and I imagine it will be especially nice on bedrock with more continuous surface ground signal coming in to base GB off of. I'm glad I did it. It allowed me to run my AA battery pack that I brought which sat at around 11.5 volts and then kick on the Gain Switch and punch deeper on tests. I didnt do measurements on all targets but lets just say IT WORKS and I hope anyone using this mod is well versed in tuning GB, Frequency, and Pulse Delay with test targets at the actual site of detection or prospecting. Very powerful in the right hands. ... I also tested my water proofed sadie coil (sika flex 221) and all was well there... Good signal above waterline to 6" deep to that 1.1gram nugget in the ziploc bag and no issues underwater. So Far So GOOD.

Here is switch installed. Tight space there. A little close to the caps lower down on board inside but cleared ok with no contact. Debating on doing the swing speed mod when caps arrive this week. @Melano87 mentioned losing depth on this mod? @Geotech or @Jim in Idaho Did you guys notice any depth changes/losses on sweep speed mod? Thanks!

Karl is the man no doubt and you guys went to great length to share your mods so I thank you again. I did the c42 jumper/on/off switch mod tonight. Taxed my skills a bit but it works. With the switch on and the gain boosted the machines emi went up a bit and I had to be careful what direction I held it in in my garage as the sadie coil was picking up anything in the structure. I put it in low conductor and GB off and it tamed down a bit. I WAS able to run GB on later in testing but I put it back in low conductive mode to avoid the coil sensing everything "big" in the garage. I was able to get it to stabilize for some hand held air testing of my sample gold nugget targets. The side of coil sensitivity went up on all sizes as did depth. At least 25-30% it seemed. Great mod so far! I may switch the R9 and R14 2512 sized resistors out for 3 watt (have 2 watt installed now, originals were 1 watt) as the battery was a little "warm" when I removed it after about 10 minutes of testing the gain switch. I'll do backyard quartz pile testing tomorrow maybe even hit river and bury some gold.

No worries. I'm sure we all have lives outside looking for treasure... Do you notice and depth increasing on signals with this mod? Sensitivity to smaller targets? Please share your thoughts on the performance you've notice if possible. Geotech recommends a 1k resistor in series with the switch to the test points. Learning as I go.. many thanks Patrick

Thanks Karl! and @Jim in Idaho The metal detector Gods have spoken... pat

You did not use a resistor? This mod is stumping me. I've been told all sorts of tech stuff I don't understand. "across" "covers" "opamp abuse". Thanks

So you didnt use a resistor? Thanks