619_805_okie Posted May 23, 2023 Share Posted May 23, 2023 Just a heads up that when trying to roll back to 0.71, my ws6 froze and now the screen wont turn on. I know many of you have liked the update but it has been nothing but crap for me and I'm not looking forward to buying a new ws6. Im hoping theyll warranty it but the phone number listed for warranty info says to email only. Really sub par customer service! Link to comment Share on other sites More sharing options...
losfinders Posted May 23, 2023 Share Posted May 23, 2023 Don't worry, they will warranty it. But first, just to save you a lot of trouble. If you purchased it from a brick and Mortar, Contact them fitst. They will handle the repair/ warranty or direct you to the nearest distributor to ship it off to. If you bought it online, look up the distributor closest to you. It will be days before you get a response from XP directly. Link to comment Share on other sites More sharing options...
martygene Posted May 23, 2023 Share Posted May 23, 2023 Try Detector Electronics in Massachusetts.... I think they are XP US distributors Link to comment Share on other sites More sharing options...
AsviS Posted May 24, 2023 Share Posted May 24, 2023 Most likely the headphone unit is frozen, wait a few days (usually up to 2 days) until the battery runs out, then charge it. It should work. Or as an option is to disassemble and reconnect the battery (just remove the battery plug and wait a few minutes and then put it back in) Link to comment Share on other sites More sharing options...
Timmysys Posted September 10, 2023 Share Posted September 10, 2023 On 5/24/2023 at 2:18 AM, AsviS said: Most likely the headphone unit is frozen, wait a few days (usually up to 2 days) until the battery runs out, then charge it. It should work. Or as an option is to disassemble and reconnect the battery (just remove the battery plug and wait a few minutes and then put it back in) I fallen is same situation, the update screen still on my ws6 puck, the USB connection disconnected when the update erase the puck. Link to comment Share on other sites More sharing options...
ecoast Posted September 10, 2023 Share Posted September 10, 2023 5 hours ago, Timmysys said: I fallen is same situation, the update screen still on my ws6 puck, the USB connection disconnected when the update erase the puck. let the battery go completely dead, then reconnect and try to update Link to comment Share on other sites More sharing options...
Timmysys Posted September 10, 2023 Share Posted September 10, 2023 7 hours ago, ecoast said: let the battery go completely dead, then reconnect and try to update Fortunately, it was solved. On another computer, after several attempts, the connection was not lost. I think the cause of the problem is the poor quality USB connector on the transmitter. All my cables are very loosely connected. 🤞 Link to comment Share on other sites More sharing options...
Shelton Posted October 4, 2023 Share Posted October 4, 2023 If WS6 froze - remove both screws under the easy-to-remove label and disconnect the mainboard from the battery. Link to comment Share on other sites More sharing options...
DWerk Posted October 15, 2023 Share Posted October 15, 2023 Tried that with mine, removed two screws, saw small 2 wire connection (red/blk) right below the display, pulled the plug, waited a few seconds, reconnected, still will not turn off/reset! Display continues to show "UPDATE". Is there another connection I am not seeing as the board is well seated in the case? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now