Steve Herschbach

The Tesoro Tiger Shark metal detector was introduced in 2000 and ceased production in 2018. The Tiger Shark is a fully submersible 12.5 kHz VLF metal detector aimed primarily at beach and underwater detecting. The Tiger Shark is submersible to 200 feet and therefore suitable for SCUBA diving. Note however that the coil and headphones are hardwired for extra waterproof integrity and are not interchangeable. There is a choice of 8" or 10.5" search coils at the time of purchase. "The Tiger Shark is hands down one of the best fresh water metal detectors on the market. This simple machine is made for the detectorist who wants to spend their time finding treasure, not memorizing special controls and techniques. The Tiger Shark’s Salt Mode changes the ground balance range to handle salt instead of minerals. This detector’s coil and headphones are hardwired to the machine to protect the machine from leaks, allowing it to be submerged up to 200 feet. Available with an 8” or 10.5” search coil." Source: Tesoro 2013 catalog Tesoro Tiger Shark metal detector Tesoro Tiger Shark control panel Operating Frequency 12.5 kHz Searchcoil Type Round, open center concentric Searchcoil Size 10½" diameter Audio Frequency Approx. 270 Hz Audio Output Stereo Piezo Headphones Weight (may vary slightly) Less than 4½ lbs. Battery Requirement Eight AA DC (alkaline) Battery Life (typical) 10 to 20 hours Optimum Temp. Range 30° to 100° F Operating Modes No-Motion All Metal (Fast & Slow Tune) Normal Mode Salt Mode Silent Search Motion Discriminate Maximum Depth Rating 200 ft Official Tesoro Tiger Shark Product Page Tesoro Tiger Shark Owner's Manual Forum Threads Tagged "tesoro detector" Tesoro Metal Detectors Forum

The Tesoro Mojave metal detector was introduced in 2017 and ceased production in 2018. It is a 12 kHz VLF metal detector aimed primarily at coin, jewelry, and relic detecting. "The Mojave is a newly designed 12 Khz detector with 2 position HIGH and LOW ground condition switch for varying soil conditions. The Mojave will broaden hunting capabilities from coast to coast! In low to moderate ground conditions the LOW setting will gain more depth. The HIGH setting will overcome the worst ground conditions while maintaining smooth and clean target responses. From land to sea and deserts to mountains, the Mojave has the power and performance to tackle any type of changing ground conditions and soil types around the world! The Precision 7” featherweight and thin profile coil is the ideal size for tough trashy areas for jewelry, coin, ring and relic hunting. Lightning fast response and retuning allow the Mojave’s 7” coil to surgically remove targets amongst the trash. Pinpointing is a snap with the new target centering reticle. New TRI-COLORED ZONES with easy identifying and adjustment in discrimination level. The Full Range 180 Discrimination covers everything from ALL METALS to screw cap rejection. WHITE, YELLOW and RED Zones from 6 o’clock to 4 o’clock for easy reference to the user." Source: Tesoro website Tesoro Mojave metal detector Tesoro Mojave control panel Stealthy Black Micro Housing and Hardware. Fully Adjustable Sensitivity. HIGH/LOW Ground Selector. Fully Adjustable Tri-Colored Zone Discrimination. Waterproof Coil. Featherweight 2.2 pounds. Fully Adjustable rods. ¼" earphone jack. External Speaker. 9 Volt Battery for 15-18 hrs. All Epsilon 5 Pin Coils Interchangeable. Limited Lifetime Warranty Official Tesoro Mojave Product Page Tesoro Mojave Owner's Manual Forum Threads Tagged "tesoro detector" Tesoro Metal Detectors Forum

The Tesoro Outlaw metal detector was introduced in 2012 and ceased production in 2018. It is a 10.6 kHz VLF metal detector aimed primarily at coin, jewelry, and relic detecting. "The Outlaw represents the return of true no motion, all-metal treasure hunting. This detector is a continuation of the Bandido series of metal detectors, which was designed with all of the controls needed to get maximum performance from its machines. Like its predecessors, the Outlaw has discrimination, sensitivity, threshold, and ground balance adjustments. Its “Retune” button is used to reduce the response from the metal, which shrinks the target area and allows for precise pinpointing. The Outlaw is available with either an 8” round concentric coil, or a three-pack of coils: 5.75” round concentric, 8” round concentric, and 12x10” widescan. The 8” coil provides great balance between depth and sensitivity, and is an efficient pinpointer. The 5.75” coil utilizes tremendous sensitivity, making it an optimal tool for pinpointing targets. The 12x10” coil is less susceptible to ground effects, which means it is perfect for heavily mineralized sites or hunting larger targets." Source: Tesoro 2013 catalog Tesoro Outlaw metal detector Tesoro Outlaw control panel MicroMAX Design Low Noise Circuitry VLF 10.6 kHz Frequency One Drop-in 9 volt Battery Silent Search Discriminate Mode No-Motion All Metal Mode Motion All Metal Mode 3-Piece Knockdown Pole Limited Lifetime Warranty Official Tesoro Outlaw Product Page Tesoro Outlaw Owner's Manual Forum Threads Tagged "tesoro detector" Tesoro Metal Detectors Forum

The Tesoro Compadre metal detector was introduced in 2000 and ceased production in 2018. It is a 12 kHz VLF metal detector aimed primarily at coin, jewelry, and relic detecting. Note that the coil on the Compadre is hardwired and not interchangeable. You can choose from one of two coil options at the time of purchase, a 5.75" or 8" concentric coil. "The Tesoro Compadre was designed with the idea that less is more. This modest machine can do a lot of the same things that its bigger brothers can do. It works great for coin hunting, competition hunting and relic hunting, but it does it without any excess knobs. Switch on the detector and you’re working in a silent search, motion all metal mode. The farther you turn the knob, the more discrimination you can bring to bear on those trashy sites. The Compadre has it all. One knob simplicity for the beginner and high gain circuitry and the famous Tesoro ED-180 discrimination for the advanced user. If one detector can do all of this, maybe less is more. The Compadre is available with a 5.75" Concentric Searchcoil or with an 8" Concentric Searchcoil." Source: Tesoro 2007 catalog Tesoro Compadre metal detector Tesoro Compadre control panel Operating Frequency 12 kHz Searchcoil Type Round concentric, hardwired Searchcoil Size 5.75" Cable Length Approx. 3' Audio Frequency Approx. 630 Hz Audio Output 1 ½" speaker and headphone jack Headphone Compatibility ¼" stereo plug Weight (may vary slightly) 2.2 lbs Battery Requirement One 9 Volt DC (alkaline) Battery Life (typical) 10 to 20 hours Optimum Temp. Range 30° to 100° F Optimum Humidity 0 to 75% R.H. Operating Modes Silent Search Discriminate Official Tesoro Compadre Product Page Tesoro Compadre Owner's Manual Forum Threads Tagged "tesoro detector" Tesoro Metal Detectors Forum

The Tesoro Silver uMax metal detector was introduced in 2001 and ceased production in 2018. It is a 10.6 kHz VLF metal detector aimed primarily at coin, jewelry, and relic detecting. "The Silver μMax represents the evolution of the Tesoro Silver Series. The Silver Series is known for its capable, uncomplicated two-knob detectors. With both a sensitivity and discrimination adjustment, the Silver μMax provides more information about your targets and the conditions of your hunt. This machine also offers the option to change search coils, enhancing the versatility of this ultra-lightweight machine." Source: Tesoro 2013 catalog Tesoro Silver uMax metal detector Tesoro Silver uMax control panel Microprocessor Technology MicroMAX Design Low Noise Circuitry VLF 10 kHz Frequency One Drop-in 9V Battery Push Button Battery Test Silent Search All Metal Mode Silent Search Discriminate Mode 8" Concentric Coil Interchangeable Coils Built-in Mineral Rejection Limited Lifetime Warranty Official Tesoro Silver uMax Product Page Tesoro Silver Umax Owner's Manual Forum Threads Tagged "tesoro detector" Tesoro Metal Detectors Forum

The Tesoro Cibola metal detector was introduced in 2004 and ceased production in 2018. It is a 14 kHz VLF metal detector aimed primarily at coin, jewelry, and relic detecting. "The Cibola is a powerful turn-on-and-go detector. It is the only detector in the Delta coil family that provides pre-set mineral rejection, which leaves the detectorist more time to hunt and less time manually readjusting to different types of soil. The Cibola is perfect for detecting with friends because of its frequency shift, which allows the user to choose between three different frequencies and eliminate interference between metal detectors. This ultra-lightweight treasure finder offers the ability to super-tune, causing the detector to overdrive small signals for better clarity. The multi-faceted Cibola does everything a more expensive detector can do, at a fraction of the weight and cost." Source: Tesoro 2013 catalog Tesoro Cibola metal detector Tesoro Cibola control panel MicroMAX Design VLF 14 kHz Frequency Pre-Set Ground Balance One Drop-in 9V Battery Variable Threshold Ultra-lightweight Design 9x8 Monolithic Coil 3-Piece Knockdown Pole Lifetime Warranty Official Tesoro Cibola Product Page Tesoro Cibola Owner's Manual Forum Threads Tagged "tesoro detector" Tesoro Metal Detectors Forum

The Tesoro Vaquero metal detector was introduced in 2004 and ceased production in 2018. The Vaquero is a 14.5 kHz VLF metal detector aimed primarily at coin, jewelry, relic, and gold nugget detecting. "The versatile Vaquero is an all-around detector designed to do just about anything a detectorist could want. Named after the Spanish word for “cowboy,” the Vaquero lives up to the hard-working, take-on-the-tough-jobs reputation that made cowboys in the Old West famous. What enhances the Vaquero’s versatility is its 3-3/4-turn manual-adjust ground balance, which gives the detectorist the capability to set up the machine to suit mineralization conditions and personal treasure-hunting style. We’ve also added an ED180 discrimination feature for filtering trash from treasure, a push-button pinpoint for easier digging, and a VCO-style all-metal operating mode—features that give the Vaquero its “do anything” power. With a weight of just under 2.2 pounds, the flexibility to use any Lobo SuperTRAQ or Tejón accessory coils, and its lifetime warranty, the Vaquero is the ultimate go-anywhere treasure tool." Source: Tesoro 2007 catalog Tesoro Vaquero metal detector Tesoro Vaquero control panel MicroMAX Design VLF 14 kHz Frequency One Drop-in 9V Battery Variable Threshold 3 3/4 Turn External Ground Balance Ultra-lightweight Design 9x8 Monolithic Coil 3-Piece Knockdown Pole Limited Lifetime Warranty Operating Frequency 14.3 kHz, 14.5 kHz, 14.7 kHz Searchcoil Type Monolithic (Carbon Fiber) Searchcoil Size 9 x 8 Searchcoil Family Delta Cable Length Approx. 3' Audio Frequency Approx. 293 Hz or VCO Audio Output 1 1/2" speaker and headphone jack Headphone Compatibility ¼" stereo plug Weight (may vary slightly) 2.2 lbs Official Tesoro Vaquero Product Page Tesoro Vaquero Owner's Manual Forum Threads Tagged "tesoro detector" Tesoro Metal Detectors Forum

The Tesoro Tejon metal detector was introduced in 2003 and ceased production in 2018. It is a 17.4 kHz VLF metal detector aimed primarily at coin, jewelry, relic, and gold nugget detecting. "The Tejon features a dual discriminator that is activated by an effortless trigger switch, allowing for an instant target check. This detector also includes a tone adjustment option, which is designed for treasure hunters who have lost the ability to hear certain audio frequencies. The Tejon pushes the coil’s signal deeper while increasing sensitivity for smaller targets. This unit is full of features that amount to more informed choices, less time digging trash, and most importantly: more time hunting." Source: Tesoro 2013 catalog Tesoro Tejon metal detector Tesoro Tejon control panel Dual ED180 Discrimination Circuits Easy To USe Trigger Mode Switch MAXBoost Sensitivity Adjustable Audio Tone Control 3-3/4 Turn Ground Control Compatible With Lobo SuperTRAQ Coils Operating Frequency 17.2 to 17.6 kHz Searchcoil Type Monolithic (Carbon Fiber) Searchcoil Size 9 x 8 Searchcoil Family Delta Cable Length Approx. 42" Audio Frequency Approx. 215 to 830 Hz Audio Output 2 ¼" speaker and headphone jack Headphone Compatibility ¼" stereo plug Weight (may vary slightly) 2.98 lbs Battery Requirement Eight AA (alkaline) Official Tesoro Tejon Product Page Tesoro Tejon Owner's Manual Forum Threads Tagged "tesoro detector" Tesoro Metal Detectors Forum

The Tesoro Cortes metal detector was introduced in 2001 and ceased production in 2018. It is a 10 kHz VLF metal detector aimed primarily at coin, jewelry, and relic detecting. "Get the best of the Epsilon series with visual and audio identification, notch filter and pre-set ground balance in discrimination mode, and manual ground adjustment in all-metal mode. The Cortes’ VID (Visual Identification) system works in two ways: the detector samples the target and provides a nine-segment bar graph of the entire signal, and a two-digit identification number shows the ID at the maximum signal strength. In addition to the expansive information provided by the VID, the Cortes boasts nine different tones for superior audio identification. Never guess a target again." Source: Tesoro 2013 catalog Tesoro Cortes metal detector Tesoro Cortes control panel Operating Frequency 10 kHz Searchcoil Type Concentric Searchcoil Size 9 x 8 Searchcoil Family Epsilon Cable Length Approx. 3' Audio Freq. Target ID Tones Approx. 350 to 800 Hz Audio Freq. All Metal VCO Approx. 350 to 920 Hz Audio Output 2 ¼" speaker and headphone jack Headphone Compatibility ¼" stereo plug Weight (may vary slightly) 2.98 lbs Battery Requirement Eight AA (alkaline) Battery Life (typical) 10 to 20 hours Optimum Temp. Range 30° to 100° F Optimum Humidity 0 to 75% R.H. Operating Modes Silent Search Discriminate, No Motion All Metal, Sum, Notch Narrow/Wide Official Tesoro Cortes Product Page Tesoro Cortes Owner's Manual Forum Threads Tagged "tesoro detector" Tesoro Metal Detectors Forum

The Tesoro DeLeon metal detector was introduced in 2003 and ceased production in 2018. It is a 10 kHz VLF metal detector aimed primarily at coin, jewelry, and relic detecting. "The DeLeón is a Target Identification Detector or T.I.D. The DeLeón is designed as an easy to use, turn-on-and-go detector. The faceplate has only four controls: Sensitivity, Discriminate, Threshold and a Mode Switch. It uses the same circuitry as the Cortés, so you can expect the same depth and sensitivity from the DeLeón that the Cortés is already well known for. The DeLeón’s display screen is one character high by eight characters wide. It is larger and easier to read than the Cortés display. Starting from left to right on the illustration, you will see that the DeLeón has a Coin Depth reading, a five segment bar graph and a two digit Target ID Number. The bar graph shows several categories for ID purposes, but we recommend that it be used with the ID Number for the most accurate information." Source: Tesoro 2007 catalog Tesoro DeLeon metal detector Tesoro DeLeon control panel Operating Frequency 10 kHz Searchcoil Type Concentric Searchcoil Size 9 x 8 Searchcoil Family Epsilon Cable Length Approx. 3' Audio Freq. All Metal VCO Approx. 350 to 950 Hz Audio Output 2¼" speaker and headphone jack Headphone Compatibility ¼" stereo plug Weight (may vary slightly) 2.98 lbs Battery Requirement Eight AA (alkaline) Battery Life (typical) 10 to 20 hours Optimum Temp. Range 30° to 100° F Optimum Humidity 0 to 75% R.H. Operating Modes No Motion All Metal Silent Search Discriminate Official Tesoro DeLeon Product Page Tesoro DeLeon Owner's Manual Forum Threads Tagged "tesoro detector" Tesoro Metal Detectors Forum

The Minelab Go-Find 66 metal detector was introduced in 2018 and is still in production. The Go-Find 66 is a 7.8 kHz VLF metal detector aimed primarily at coin, jewelry, relic, and beach detecting. "Advance your hunting to the next level. GO-FIND 66 is a serious, high-tech detector. It delivers precision, performance and maximum depth to unearth more treasure. Packs in a load of excitement and adventure, too. Hunt like a pro today. Superior Performance - Advanced technology and innovative features for performance to the MAX. Compact & No Assembly - It’s easy. There’s nothing to assemble and no loose parts that can get lost. Ultra Lightweight - At only 2.3 lbs (1.06 kg). Easy-Trak Automatic - Auto ground-tracking reduces noise interference and maximizes target signals. Treasure View - Red = iron targets, likely trash. Green = non-iron targets, possibly treasure! Step up to the power, performance and ultimate technology of the GO-FIND 66. Go wild, find adventure like a pro." Source: Minelab website Minelab Go-Find 66 metal detector Minelab Go-Find 66 control panel Portability Collapsible Body Find Modes 4 Search Coil Large (10-inch waterproof coil) Treasure View 5 LEDs Backlight Yes Sensitivity 5 Levels Volume 5 Volume Levels Pinpoint Locating Yes Bluetooth Yes Smartphone App Pro Version Smartphone Holder Yes Digging Tool Yes Earbuds Yes Batteries 4xAA Batteries (not inc.) Length Collapsed 21.9 in / 555 mm Length Extended 51.4 in / 1305 mm Weight 2.3 lbs / 1.06 kg Official Minelab Go-Find 66 Product Page Minelab Go-Find 66 Getting Started Guide Minelab Metal Detector Forum

The Minelab Go-Find 44 metal detector was introduced in 2018 and is still in production. The Go-Find 44 is a 7.8 kHz VLF metal detector aimed primarily at coin, jewelry, relic, and beach detecting. "When you want that edge, that advantage and a powerful sense of discovering more than you thought possible, GO-FIND 44 takes you there. Prepare to unearth what lies deep beneath your feet with your GO-FIND 44. Superior Performance - Advanced technology and innovative features for performance to the MAX. Compact & No Assembly - It’s easy. There’s nothing to assemble and no loose parts that can get lost. Ultra Lightweight - At only 2.3 lbs (1.06 kg). Easy-Trak Automatic - Auto ground-tracking reduces noise interference and maximises target signals. Treasure View - Red = iron targets, likely trash. Green = non-iron targets, possibly treasure! Search deeper and find the treasure other people miss with the GO-FIND 44." Source: Minelab website Minelab Go-Find 44 metal detector Minelab Go-Find 44 control panel Portability Collapsible Body Find Modes 3 Search Coil Large (10-inch waterproof coil) Treasure View 5 LEDs Backlight Yes Sensitivity 4 Levels Volume 5 Volume Levels Pinpoint Locating Yes Bluetooth Yes Smartphone App Standard Version Batteries 4xAA Batteries (not inc.) Length Collapsed 21.9 in / 555 mm Length Extended 51.4 in / 1305 mm Weight 2.3 lbs / 1.06 kg Official Minelab Go-Find 44 Product Page Minelab Go-Find Getting Started Guide Minelab Metal Detector Forum

The Minelab Go-Find 22 metal detector was introduced in 2018 and is still in production. The Go-Find 22 is a 7.8 kHz VLF metal detector aimed primarily at coin, jewelry, relic, and beach detecting. "Experience the excitement of treasure discovery with the GO-FIND 22. Ultra-lightweight and simple to operate, it’s about getting the whole family involved. Designed for people of all ages, the GO-FIND 22 is ideal for your next camping adventure. Start detecting today. Compact & No Assembly - Portable and easy to transport. Unfold and go. Packs down just as fast. Ultra Lightweight - At only 2.2 lbs (1.00 kg). Preset Find Modes - Icons flash to tell you what you’ve found. There’s nothing difficult and everything innovative and smart about the GO-FIND 22." Source: Minelab website Minelab Go-Find 22 metal detector Minelab Go-Find 22 control panel Portability Collapsible Body Find Modes 2 Search Coil Regular (8-inch waterproof coil) Sensitivity 3 Levels Volume 5 Volume Levels Batteries 4xAA Batteries (not inc.) Length Collapsed 21.9 in / 555 mm Length Extended 51.4 in / 1305 mm Weight 2.2 lbs / 1.0 kg Official Minelab Go-Find 22 Product Page Minelab Go-Find 22 Getting Started Guide Minelab Metal Detector Forum

The Minelab Safari metal detector was introduced in 2009 and is still in production. The Safari is a multifrequency VLF metal detector aimed primarily at coin, jewelry, relic, and beach detecting. "Powered by Minelab's Full Band Spectrum (FBS) multiple frequency technology, the Safari combines deep, sensitive and accurate detecting for anyone demanding both simplicity and performance. Safari uses advanced digital filtering to eliminate the influence of ground signals automatically so you can experience easy, seamless detecting whatever the field conditions. With its High Trash Density setting, Target Ids and audio tones are updated when sweeping over closely spaced targets fast! This improves the recovery of deeply buried high conductivity targets in a trashy environment and allows you to more accurately identify the type of target found. The Safari is also available in the Safari Pro Pack which includes RPG PH100R Headphones with adjustable headband and left and right channel volume controls, a NiMH rechargeable Battery Pack and a mains battery charger (240v or 110v version depending on country). Discover the adventure and excitement of detecting with a Safari today!" Source: Minelab website Minelab Safari metal detector Minelab Safari control panel FBS multiple frequency technology. Ultra-lightweight 11" Double-D waterproof coil combines high performance, great depth and sharp pinpointing. Four pre-programmed detection modes - Coin; Coin/Jewellery; Relic and All Metal. Each individual mode contains the optimum settings for identifying the characteristics of your preferred targets, allowing you to maximise your time in the field. Pinpoint with audio and visual indicators for more accurate detection – press the pinpoint button and watch the Safari zone-in on the precise location of that precious target. Trash Density - High ensures fewer false signals experienced in typical coin and relic environments so you don’t waste time digging for junk, while low is ideal for clean sites to make sure you don’t miss anything. Target Volume Adjust - adapts target signal volume to suit user preference. Noise Cancel - automatically selects the quietest, most stable channel for detecting. Intuitive menu interface for fast and easy access and adjustment. Robust, well balanced design and long lower shaft for comfortable detecting over longer periods. Official Minelab Safari Product Page Minelab Safari Owner's Manual Minelab Metal Detector Forum

The Minelab Excalibur II metal detector was introduced in 2008 and is still in production. The Excalibur II is a fully submersible multifrequency VLF metal detector aimed primarily at coin, jewelry, and saltwater beach detecting. The 200 foot maximum depth makes the Excalibur II suitable for use while SCUBA diving. Note that as a diving detector both the headphones and coil are hardwired into the control box and cannot be changed. "The World’s Best Water Detector! Minelab’s unique Broad Band Spectrum (BBS) technology, combined with superior ground rejecting technology, makes the Excalibur II the ideal underwater machine. The design of the Minelab Excalibur II allows you to use it as effectively in or out of the water - this amphibious machine can move seamlessly from land, beach and wet sand conditions to underwater depths of up to 200 ft (66m). With superior ground cancelling, false signals from detecting in salt water are greatly reduced. Enjoy the simple yet effective discrimination and be surprised at the sensitivity and depth you uncover targets from. Whether you are a long time diver or a casual beachcomber the Excalibur II is unbeatable for working the beach, wading in the shallows or diving a wreck at 200 feet for treasures." Source: Minelab website Minelab Excalibur II metal detector Minelab Excalibur II control panel BBS multiple frequency technology (1.5kHz – 25.5kHz). RCB amplifies weak target signals inside the coil, reducing noise and boosting faint, deep objects. High Visibility fluorescent bodywork and skidplate Slimline 10" coil for reduced weight and improved balance. NiMH Rechargeable battery pack for operation up to 12 hours. Side-mount shaft for shallow and surf-wading (available as an optional accessory). Official Minelab Excalibur II Product Page Minelab Excalibur II Owner's Manual Minelab Metal Detector Forum

The Minelab Equinox 600 metal detector was introduced in 2018 and is still in production. The Equinox 600 is a fully submersible VLF metal detector aimed primarily at coin, jewelry, relic detecting, and saltwater beach detecting. The Equinox 600 is a multifrequency detector that can also run at one of several single frequencies: 5, 10, and 15 kHz. "With innovative NEW simultaneous multi-frequency technology, the EQUINOX Series redefines all-purpose detecting for the serious enthusiast. Equally adaptable for all target types and ground conditions, just set your detecting location and go!" Source: Minelab website Minelab Equinox 600 metal detector Minelab Equinox 600 control panel Simultaneous Multi-Frequency - True intelligent Simultaneous Multi-Frequency for maximum performance, plus a wide range of single frequencies. 6 Custom Search Profiles - Each Detect Mode features 2 custom Search Profiles so you can save your favourite settings in each mode. Waterproof Design - EQUINOX is fully submersible, ideal for detecting at the beach and in rivers, streams and lakes. (3m / 10-feet) Fast & Accurate Target ID - Fast recovery speed with accurate Target ID ensures you won’t miss any valuable targets amongst the trash. Sleek & Lightweight - Rugged and lightweight construction allows you to enjoy long detecting sessions in any environment. Wireless Audio Compatible - Compatible with ultra-fast wireless audio with the WM 08, and fast aptX™ Low Latency / Bluetooth headphones. Official Minelab Equinox 600 Product Page Minelab Equinox 600 Owner's Manual Forum Threads Tagged "minelab equinox" Minelab Equinox Metal Detector Forum

The Minelab Gold Monster 1000 metal detector was introduced in 2017 and is still in production. It is a weatherproof 45 kHz induction balance metal detector aimed primarily at gold prospecting. The normal sales package for this detector includes two coils, a 5" round DD coil, and a 6" x 10" DD coil. "The GOLD MONSTER 1000 features fully automatic operation and comes with a choice of coils, battery options and shaft configurations. If you're looking for super sensitive gold performance at a great price, then this is the detector you've been waiting for!" Source: Minelab website Minelab Gold Monster 1000 metal detector Minelab Gold Monster 1000 control panel Fully automatic operation Extra sensitive 45 kHz VLF performance Highly adaptable 2 search coils included Easy quick start Official Minelab Gold Monster 1000 Product Page Gold Monster 1000 Getting Started Guide Minelab Gold Monster 1000 - Steve's Review Forum Threads Tagged "minelab gold monster" Minelab Metal Detector Forum

The Minelab SDC 2300 metal detector was released in 2014 and is still in production. The SDC 2300 is a fully submersible pulse induction (PI) metal detector aimed primarily at gold prospecting but with possible applications for saltwater beach detecting. Note that the SDC 2300 8" round mono search coil is hardwired into the control box and cannot be changed. "This compact waterproof detector comes with easy-to-use controls and is assembly-free. Quickly find more gold patches and more gold nuggets! The SDC 2300 was field tested by Minelab professional testers in real gold fields (heavily mineralised) and delivered proven results. "SDC 2300 strikes gold in field test land previously hunted by another (brand) midrange machine" - Minelab field tester. “You will find more small nuggets and fine-threaded specimen gold in mineralised soils with the SDC 2300 than any other gold detector, including the GPX 5000.” “The SDC’s unique advantage is ultra-low ground noise in mineralised and saline soils AND very high sensitivity to fine gold and fine targets (like chains) at the beach.” - Bruce Candy (Chief Scientist Minelab Electronics, SDC Inventor)." Source: Minelab website Minelab SDC 2300 metal detector Minelab SDC 2300 control panel Compact - Folds to small portable size, 8.5” (216mm) by 15.7” (400mm). Fits into carry-on luggage and most backpacks. Waterproof Capability - Fully submersible to 10’ (3m) for detecting riverbeds and shorelines, allowing you to transition with ease from land to water. Rugged & Assembly Free - Military grade construction, one piece detector designed to perform in the toughest conditions. No assembly required. Easy Patch Hunting - Search quickly and efficiently in hard to reach and remote places to find those elusive gold bearing clustered deposits. MPF (Multi Period Fast) technology incorporates extremely fast Pulse Induction switching between Transmit (Tx) and Receive (Rx) detector signals. Therefore minimal residual transmit signal is present during the receive cycle, enabling clear sharp detection of very small gold. Official Minelab SDC 2300 Product Page Minelab SDC 2300 Owner's Guide Minelab SDC 2300 - Steve's Review Forum Threads Tagged "minelab sdc 2300" Minelab Metal Detector Forum

The Minelab GPX 4500 detector was released in 2008 and discontinued in February 2021. The GPX 4500 is a pulse induction (PI) metal detector aimed primarily at the gold prospecting market but which has become popular also with relic hunters. Note that the sale price of this model normally includes two search coils, an 11" round DD plus an 11" round mono coil. "Return of the Legendary Gold Detector! The versatile GPX-4500 is a proven gold finder with many features and great performance. Incorporating Minelab’s superior Multi Period Sensing (MPS), Dual Voltage Technology (DVT) and Smart Electronic Timing Alignment (SETA) technologies it penetrates mineralised ground better and deeper than basic PI detectors." Source: Minelab website Minelab GPX 4500 metal detector MPS, DVT & SETA technologies for superior gold detecting performance. 2 coils supplied: 11-inch Double-D for general use AND 11" Monoloop for deeper detecting Versatile Timing settings for various ground conditions. The Enhance timing is a powerful feature, similar to the Sensitive Smooth timing, but provides an improvement in the depth and signal response on small and large targets alike. The Sharp timing is more suited to quieter soils and can also help to pinpoint faint targets. Six pre-programmed search modes for easy switch-on-and-go detecting. All six search modes can be modified with your favourite settings and renamed. Stabilizer control for the smoothest threshold. In noisy conditions, turning it down will provide you with a smoother threshold. In quiet conditions, increase the stabilizer and faint target signals will be more obvious. Ground Balance OFF for neutral soils. This is a useful feature for very benign low mineralised or salt saturated soils. This setting will also work well for treasure or relic hunters in loam or sandy soils. Backlight with adjustable time-out to preserve battery life. Target Volume allows you to increase the strength of softer target signals. This is useful in windy conditions, for people suffering from hearing loss, and to adjust the audio volume when using external speakers. This can also provide an audio boost in mild soils, and can be used to smooth out ground noise signals in highly mineralised soils. The Iron Reject function allows you to set the desired level of discrimination, from cautious to aggressive. This enables detecting in areas with high levels of ferrous junk. Built-in amplifier so you can hear soft target signals from deeper nuggets, more easily. The Li-lon battery pack includes a built-in audio amplifier, allowing you to use an external speaker without the need for any external booster. Official Minelab GPX 4500 Product Page Minelab GPX 4500 Owner's Manual Minelab GPX 4500 - Steve's Review GPX 4000 - 5000 Timing Charts Forum Threads Tagged "minelab gpx" Minelab Metal Detector Forum

The Minelab GPX 5000 detector was released in 2010 and is still in production. The GPX 5000 is a pulse induction (PI) metal detector aimed primarily at the gold prospecting market but which has become popular also with relic hunters. Note that the retail price of this detector normally includes two coils, an 11" round DD plus a 12" x 15" mono coil. "Gold detecting is a fascinating and rewarding activity enjoyed by people all over the world. By getting to know your GPX Series detector you can become one of the many who find gold and valuable treasure on a regular basis. The GPX 5000 and GPX 4800 are high precision instruments incorporating Multi-Period Sensing (MPS), Dual Voltage Technology (DVT), Smart Electronic Timing Alignment (SETA), and advanced digital processing. The GPX 5000 and GPX 4800 will locate gold in all types of ground, especially highly mineralised ground conditions, with great efficiency. This manual is designed to help both the beginner and expert prospector get the best performance out of their GPX 5000 and GPX 4800." Source: Owner's Manual Minelab GPX 5000 metal detector Minelab GPX 5000 controls MPS, DVT & SETA Technology 8 Timings make the GPX 5000 very versatile. It's like having 8 detectors in 1. In addition to five of the Timings found on the previous model the GPX 5000 introduces three new Timings: Coin/Relic, Salt/Gold and Fine Gold. Fine Gold Timing gives even more depth and sensitivity than Enhance — bring home more nuggets even from ground thought to be completely worked out! Salt/Gold Timing is great for all nugget sizes in salty ground — outstanding at the beach! Coin/Relic Timing is the deepest ever for benign ground conditions. Improved Enhance Timing for more depth Improved electronics for increased target sensitivity and ground balance performance Six preset Search Modes gives you easy switch on and go detecting. In addition to General and Deep search are: Hi-Mineral, Patch, Hi-Trash and Pinpoint. All six Search Modes can be modified to your personal favourite settings. Menu accessible Search Modes can also be renamed. Increased Rx Gain adjustment allows you more precise sensitivity control for optimum performance. Automatic Ground balance options make it easy to adjust the detector to suit all ground conditions. e.g. (Fixed, Tracking, Tracking speed, Ground Balance Type, Quick-Trac button). Audio adjustments to maximize target signals for your personal hearing ability e.g. (Threshold, Tone, Audio Type, Signal Peak, Response, Target Volume, Volume limit, Stabilizer). Iron Reject adjustable to suit the iron trash level where you are detecting. Motion control, adjustable to match your sweep speed and optimise target responses. Tune (also known as Noise Cancel) - Automatic and Manual options to minimize electrical interference. Backlight so that you can read the LCD menu in any light, allowing you to detect day or night. The back light also has an adjustable timeout to help preserve battery power. Lightweight Li-ion Battery with inbuilt Speaker Booster capability Two coils as standard: 11” Double-D coil plus 15 x 12-inch Monoloop coil giving you added versatility and value. Languages: English, Spanish, Russian & Arabic (manual only) Official Minelab GPX 5000 Product Page Minelab GPX 4800 | 5000 Color Brochure Minelab GPX 5000 Owner's Manual Minelab GPX 5000 - Steve's Review GPX 4000 - 5000 Timing Charts Forum Threads Tagged "minelab gpx" Minelab Metal Detector Forum

The Minelab X-Terra 305 metal detector was introduced in 2009 and is still in production. The X-Terra 305 is a selectable frequency VLF metal detector aimed primarily at coin, jewelry, and relic detecting. The X-Terra models are unique in that they sense the coil attached to the detector, and then match the detector frequency to the coil. Coils are made in 3 kHz, 7.5 kHz, and 18.75 kHz versions but note that the 305 cannot use the 3 kHz coils. The X-Terra 305 comes standard with a 7.5 kHz 9" round concentric coil. "When value for money really matters, then the X-TERRA 305 is best in class! The X-TERRA 305 is the entry level detector in the Minelab X-TERRA Series. A lightweight, easy to use, coin and treasure-hunting detector designed for the hobbyist who does not want or need the top of the range machine. The X-TERRA 305 is suitable for the whole family and there is even a short shaft available for keen youngsters. Despite being ultra lightweight and so easy to use there is no compromise on quality or performance - Minelab’s designers used innovative, lateral thinking and the very latest in digital components to design the X-TERRA Series of detectors. The X-TERRA 305 is now packed with new features, functionality and enhanced setting options. This detector delivers results, value and more…in fact some might think that we made it too good!!! A no nonsense detector perfect for those seeking a high performance entry-level detector. Note: THIS PRODUCT IS NO LONGER AVAILABLE FOR SALE IN AUSTRALIA." Source: Minelab website Minelab X-Terra 305 metal detector Minelab X-Terra 305 control panel Minelab’s proprietary VFLEX technology, then new class of single frequency detectors – you can change the operating frequency simply by changing coils. Compatible with Medium Frequency (7kHz) and High Frequency (18.75kHz) coils – 6 accessory coil options offer increased versatility. Accurate Ground Balance capability with manual adjustment of 0-20, allows the user to adjust to ground mineralization easily. 2 preset patterns, that can also be customised, plus All-Metal mode. Choice of 1,2 or 3 tone ID’s plus multi-tone Target ID (12) response. This allows greater flexibility in deciding how target signals are represented. Threshold adjustment, with a range of -5 to 25 allowing the user to set threshold to levels where slight variations from either very small shallow, or very large deep, targets can be noticed. Noise Cancel function with 3 manual settings allowing the user to pick the quietest channel for detecting. Rapid recovery Pin-Point with variable tone and graphical indicator. Target Volume adjust (0-10) allowing you to get more definitive audio information on each target. Depth indicator, updates continuously, even in Pinpoint mode. Positive reflective LCD display. Runs on just 4 x AA batteries. Ultra lightweight, balanced design (only 1.3kgs including battery). Official Minelab X-Terra 305 Product Page Minelab X-Terra 305 Owner's Manual Forum Threads Tagged "minelab x-terra" Minelab Metal Detector Forum

The Minelab X-Terra 505 metal detector was introduced in 2009 and is still in production. The X-Terra 505 is a selectable frequency VLF metal detector aimed primarily at coin, jewelry, and relic detecting. The X-Terra models are unique in that they sense the coil attached to the detector, and then match the detector frequency to the coil. Coils are made in 3 kHz, 7.5 kHz, and 18.75 kHz versions. The X-Terra 505 comes standard with a 7.5 kHz 9" round concentric coil. "The perfect all rounder! The X-TERRA 505 is a high performance, mid-range detector in the Minelab X-TERRA Series. With advanced capability, great depth and excellent discrimination, the X-TERRA 505 is the ideal all-rounder to take your detecting experience to the next level. The X-TERRA 505 has 3 frequency capability and can adapt easily to coin & treasure and relic hunting." Source: Minelab website Minelab X-Terra 505 metal detector Minelab X-Terra 505 control panel Minelab’s proprietary VFLEX technology, the new class of single frequency detectors – you can change the operating frequency simply by changing coils. Compatible with low frequency (LF) 3kHz coils as well as medium 7kHz and high frequencies 18.75kHz. The LF coil option is ideal for hunting large, deep targets. All X-TERRA Coils can be used on the X-TERRA 505. Increased Ground Balance capability, range now (0-50), allowing the user to adjust to ground mineralization. Extra detecting pattern – Now features three preset detecting patterns, that can also be customised, plus All Metal mode. Choice of 1,2,3 or 4 Tone ID’s plus Multi-tone Target ID (19) response options increasing your flexibility in deciding how target signals are represented. Larger discrimination range allowing for finer discrimination of high conductive targets. Increased Noise Cancel range, now 5 manual settings, allowing greater choice of detecting channel. Increased Target Volume Adjust range, now (0-30), allowing better target response. Threshold adjustment, with a range of -5 to 25, allowing the user to set threshold to level where slight variations from either very small shallow, or very large deep, targets can be noticed. Fast recovery Pin-Point with variable tone and graphical indicator. Depth indicator, updates continuously, even in Pinpoint mode. Positive reflective LCD display. Runs on just 4 x AA batteries. Ultra lightweight, balanced design (only 1.3kgs). Official Minelab X-Terra 505 Product Page Minelab X-Terra 505 Owner's Manual Forum Threads Tagged "minelab x-terra" Minelab Metal Detector Forum

The Garrett Sea Hunter Mark II metal detector was introduced in 1999 and is still in production. The Sea Hunter is a fully submersible pulse induction (PI) metal detector aimed primarily at beach and underwater detecting. The Sea Hunter Mark II is submersible to 200 feet and therefore suitable for SCUBA diving. "The Garrett Sea Hunter Mark II has an unparalleled reputation among treasure hunters, law enforcement agencies and various industries as one of the most reliable and sophisticated submersible metal detectors of its kind. The Sea Hunter Mark II is an advanced microprocessor-driven instrument that is lightweight, highly durable and easy to use. The Sea Hunter's pulse induction (PI) circuitry provides excellent depth and enables you to find treasure without interference from salt water and most ground minerals." Source: Owner's manual Garrett Sea Hunter Mark II metal detector Garrett Sea Hunter Mark II control panel Circuit type: Pulse Induction technology for automatic cancellation of salt/ground mineralization Audio Threshold, Adjustable: adjust to user’s preference User-adjustable Discrimination/Elimination Hip Mount Belt/Pouch: reduces detector weight for long searches Discrimination Modes: Two operating modes (Standard or Discrete) offer varying levels of non-ferrous target discrimination. Discrete Trash Elimination: use to eliminate most pull tabs and foil without significantly degrading sensitivity for rings and coins. Standard Trash Elimination: provides the deepest possible detection; allows a very slow searchcoil sweep in areas with little trash. Independently sealed battery compartment Search Mode: Non-Motion All Metal Deepseeking Mode with Full Range PI discrimination Official Garrett Sea Hunter Mark II Product Page Garrett Sea Hunter Mark II Owner's Manual Garrett Metal Detector Forum

The Garrett ATX metal detector was introduced in 2013 and is still in production. The ATX is a fully submersible ground balancing pulse induction (PI) metal detector aimed primarily at relics, gold prospecting, and beach detecting. "High-End, All-Terrain Pulse Performance. Highly sensitive on tiny gold and extends depth in the most extreme mineralized soils. HUNT ONCE, GET IT ALL." Source: Garrett 2018 catalog Garrett ATX metal detector Garrett ATX control panel Maximum Detection on all targets at the same time. No need to switch modes to enhance detection of one target while degrading another. Advanced Ground Balance Has wide range to ground balance from heavily mineralized ground (ironstone) to saltwater without switching to special modes. Quick Iron Check feature Allows the operator to audibly identify iron targets when using a DD searchcoil. Quickly and Fully Collapsible Rugged military-spec design Motion and Non-Motion Modes Provides optimum performance based on your hunting preference and conditions. All Terrain use: Weatherproof design for dusty, humid, or wet environments; and fully submersible to 10-foot depth. Adjustable Sensitivity, Discrimination, Volume, and Frequency Scan Each can be adjusted with one hand. Ground Track (Automatic) Choose from four tracking speeds to have the ATX continuously measure ground mineralization and automatically adjust itself for optimum performance. Advanced DD searchcoil Provides easy pinpointing and enhanced detection of small items without having to slow the scanning speed of the searchcoil. Official Garrett ATX Product Page Garrett ATX Owner's Manual Garrett ATX - Steve's Review Forum Threads Tagged "garrett atx" Garrett Metal Detector Forum

The Garrett GTI 2500 metal detector was introduced in 1999 and is still in production. The GTI 2500 is a 7.2 kHz VLF metal detector aimed primarily at coin, jewelry, and relic detecting. "See a Target’s Size and Depth! Spend less time digging trash and more time digging treasure. Graphic Target Imaging™ (GTI) Garrett Exclusive feature that shows true target size (5 size options) and depth." Source: Garrett 2018 catalog Garrett GTI 2500 metal detector Garrett GTI 2500 control panel Graphic Target Imaging™ (GTI) shows true target size and depth. Watch "Imaging by Garrett" video Graphic Target Analyzer™ (GTA) identifies target’s conductivity True Digital Signal Processor™ (DSP) improves discrimination accuracy ScanTrack™ optimizes treasure signals based on searchcoil swing speed Ground Balance: automatic and also manually adjustable All Metal, Non-Motion Deepseeking Mode: allows hovering over target User-adjustable Volume, Threshold, Tone, Sensitivity, Discrimination Salt Elimination Aid: eliminate interference caused by wetted salt at beach Hip Mount Battery Pack: reduces detector weight for long searches FastTrack™ Ground Balance for use in All Metal Mode Surface Elimination: adjustable search aid ignores shallow, undesired items LCD Backlight: to illuminate LCD screen for improved visibility External Speaker and Headphone Jack: quarter-inch (1/4") size Coin Alert Belltone Audio™: Garrett sound for high conductivity targets Last Mode Switching: switch from All-Metal into last-used discrim. mode Official Garrett GTI 2500 Product Page Garrett GTI 2500 Owner's Manual Garrett Metal Detector Forum