GB_Amateur Posted August 9, 2022 Share Posted August 9, 2022 1 hour ago, phrunt said: stricks very useful 11" coil X-ray, the coil cable doesn't look wrapped in foil to me, would the X-ray not pick up the foil as a solid mass and not show the wires inside it if it was foil or braided? Depends a lot upon the shielding material used (aluminum is more transparent than copper) and the energy of the X-rays (higher energy being less absorbed, in general). @strick has done X-ray imaging of other coils. Do their cables show shielding? I think braid is plated/coated copper (or sometimes just raw Cu with no surface treatement), but far from sure. 2 Link to comment Share on other sites More sharing options...
phrunt Posted August 9, 2022 Share Posted August 9, 2022 On 8/9/2022 at 1:00 PM, GB_Amateur said: @strick has done X-ray imaging of other coils. Do their cables show shielding? The braided ones certainly show, and some just show a solid mass. A couple of what looks to be a solid mass examples and Braided examples The cable you showed from the component looks possibly braided to me when zoomed in. 2 Link to comment Share on other sites More sharing options...
Chet Posted August 9, 2022 Share Posted August 9, 2022 Most EMI is picked up by the coil. The coil receives EMI similar to the antenna of an AM radio. The larger the coil surface the more EMI is detected. Proper EMI shielding of the coil is the most critical factor. For a low impedance mono coil the approximate three foot of lead can be a twisted pair of unshielded wires and be very effective in canceling EMI. It does this by the EMI on each wire being balanced and of opposite voltages being introduced by the twisted wires receiving equal and opposing EMI signals. With a Double D coil the low impedance transmit wires are often a unshielded twisted pair. The higher impedance sensitive receive coil is normally connected by a small diameter shielded cable. 3 2 Link to comment Share on other sites More sharing options...
phrunt Posted August 9, 2022 Share Posted August 9, 2022 I was hoping you would chime in Chet, thanks! Link to comment Share on other sites More sharing options...
phrunt Posted August 9, 2022 Share Posted August 9, 2022 We always used shielded Cat6, what's the point using the cheaper twisted version when the price is so close to the same for the much better quality shielded cables. Even in a home situation there are many appliances and power cables running through the house to interfere, and fluro lights are killers for Ethernet cables. Shielding helps protect the data from any sort of electromagnetic interference from an outside source. This could alter or weaken the signal traveling through the copper in the cable. The shields of the two connectors in our shielded Cat 6 cables are electrically tied together via the drain wire. I never understand any place that tries to save a few cents by going cheap on things that are so cheap and easy to use an improved version. 3 Link to comment Share on other sites More sharing options...
phrunt Posted August 10, 2022 Share Posted August 10, 2022 New toy arrived! It arrived too late in the day to test it out. The water hunters will be pleased to see it has a nice solid base under the skid plate so it won't fill with water. Will give it a spin tomorrow and see how it goes on some test targets, then should be able to go for a gold hunt Friday, got too much to do tomorrow for that. Feels solid as a rock, really nice tough build quality. People won't need to put protective stickers on these coils that's for sure, such a different plastic. 3 Link to comment Share on other sites More sharing options...
strick Posted August 10, 2022 Share Posted August 10, 2022 The radiographs are slightly under exposed in the first two you show Simon the plastic details well but under exposing the metal showing less detail thus the solid looking mass... the ones I took are slightly over exposed showing better detail of the wiring...and less of the plastic...adjusting the power and the time on the generator you can manipulate the picture to show softer structures or more dense structures accordingly. I was hoping coiltek would chime in on how their coils are built. They certainly look good from the outside lol strick 2 1 Link to comment Share on other sites More sharing options...
Popular Post Coiltek Posted August 11, 2022 Author Popular Post Share Posted August 11, 2022 On 8/8/2022 at 7:53 PM, strick said: Most of the talk has been about coil shapes and sizes...the excitement reminds me of kids ordering ice cream in a store....I’d like to know more about how they are built compared to your competitors? NF goes into a little detail about their construction methods on their web site...I could not find much on yours...What are the components that go into the build quality of your coils? From out side to inside. Strick Hi All - been away for a bit out West on a sales trip and running the coils... Geez I like them but some would say I am bias ? A quick run down for you.... ABS plastic injection moulded housings - 2mm thick for extra strength and assist with minimising any flex when swinging Cable and internal PCB parts all same as Minelab (as do NF coils) - I can assure all that the cables are shielded very well and I do not believe that if there are any issues that the cable contributes to this. High grade LITZ wire - same as what is int he ML coils. in-spec shielding top and bottom of coil Pressure regulation pad to keep out water and dust but assist to regulate the pressure in the coil to minimise any swelling and induced noise Wings thickened for robustness and 8mm nylon nut and bolt. Poly carb label to look good - always! ? All made in our Salisbury South manufacturing facility where we have 13 staff plus me (sales and technical) and my wife (CEO & Marketing) building coils and also making electronic windings (inductors,transformers etc) inc. QA, Engineering, Customer Service etc and all other things to keep a small-medium business running... I hope this answers your query on this... Regards, Trevor. 10 5 Link to comment Share on other sites More sharing options...
strick Posted August 11, 2022 Share Posted August 11, 2022 Thanks for the response Trevor...the other guy uses core cell in their coils its good stuff but expensive the reason I know is I’ve bought plenty of for use on boats . Do you use a light weight foam coring as well? strick Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now