martygene Posted September 17, 2022 Share Posted September 17, 2022 Give us your review please. I still havent tried it. Been using fast and deep hc. Maybe a good discussion of the 3 of them would be good for us all. Link to comment Share on other sites More sharing options...
CPT_GhostLight Posted September 17, 2022 Share Posted September 17, 2022 I really don't use General much in my soil. I mostly use Fast, Relic, and occasionally Park, and use Single Frequency to cross check iffy targets. I did experiment with General a few days ago on wet ground to see if it would be better than my usual programs, but I ended up going back to Fast and like it better for my soil, wet or dry. Here's a video I stumbled across that might be of some use in this dicussion. It shows General vs a modified Park program on live digs and he shows all the settings of each program. https://www.youtube.com/watch?v=TbZySv0Irwo 1 Link to comment Share on other sites More sharing options...
broadfield Posted September 17, 2022 Share Posted September 17, 2022 General uses the widest span of frequencies out of all the programs, I use it on new sites to get a feel. Then swap to sensitive if it need the weighting at higher frequencies or park / deep hc if I need a lower frequency weighting. 2 Link to comment Share on other sites More sharing options...
bigtim1973 Posted September 17, 2022 Share Posted September 17, 2022 I started out with it to get a feel of the unit and get used to the machines responses and all. Worked good but now mostly use a modified program 4 fast. I just like the way program 4 responds and so far I have discovered it is fairly deep as well. First signal I dug with my deus 2 on general was a nickel on edge about 6 inches deep. It locked on good and proved itself on that first dig. Like I mentioned now though....I use program 4 with full tones and the square audio. Have set the recovery to 2.5. Will go lower when needed. No disc or notch settings. Love it. 1 Link to comment Share on other sites More sharing options...
ColonelDan Posted September 18, 2022 Share Posted September 18, 2022 I use a modified General program when in fresh water lakes. Nice and smooth, quiet and effective. 2 Link to comment Share on other sites More sharing options...
basstrackerman Posted September 18, 2022 Share Posted September 18, 2022 I use modified park mostly. Also deep HC but I get more emi with deep HC and need to lower sensitivity to 80-88 . Park is quiet and deep and I can run max sensitivity 2 Link to comment Share on other sites More sharing options...
palzynski Posted September 18, 2022 Share Posted September 18, 2022 I mostly use SENSITIVE 5 tones + SQUARE . GENERAL is too slow for me it doesnt like iron trash. However GENERAL is a good program to start with the D2 . 2 Link to comment Share on other sites More sharing options...
Zord Posted September 18, 2022 Share Posted September 18, 2022 General is my favorite, because it rejects the moisture in the soil. Perfect program for spots, that most diggers try to avoid. Swamps and other damp places, last resort of real treasures. https://en.wikipedia.org/wiki/Illerup_Ådal 3 Link to comment Share on other sites More sharing options...
Wheeler925 Posted September 19, 2022 Share Posted September 19, 2022 I also use a modified park program. I too get more EMI with deep HC, but it has its place. I don't understand Zord's comment about wet spots being avoided.. is this some new fad? 1 Link to comment Share on other sites More sharing options...
Lodge Scent Posted September 19, 2022 Share Posted September 19, 2022 I think Zord is saying just the opposite.......The wet spots are the only good spots left that haven't been searched out. 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now