Jump to content

Tdi Pro Coil Comparison On The Goldfields


karelian

Recommended Posts

I think this chart was lost due to websites going offline, etc. It is by Reg Sniff, and attempts to illustrate the White's TDI tone shift on some targets, at different ground balance settings. Where the colored lines cross the “minimal audio change” line the object has fallen into the hole and is eliminated. At proper ground balance settings of around 8 on common ground the TDI exhibits a huge loss or inability to detect nuggets in the 1/4 ounce range, but due to nugget variability the actual loss is extremely hard to predict. See my photo chart below as to why that is.

whites-tdi-tone-response-chart-reg-sniff.jpg
Gold nugget target id numbers metal detector herschbach
Gold nugget target id numbers Source

  • Like 5
Link to comment
Share on other sites


I have Reg's chart taped to the bottom of my SL. If I haven't used the SL for awhile, it's good to be able to refer to it.

Jim

Link to comment
Share on other sites

Thank you Steve for your excellent explanation of the condition!

I know you have a LOT of experience specifically with the TDI from literally years of ueu (as well as most machines around), and since that's what I am using because I cannot justify a more sophisticated PI machine right now, I was wondering how those of us still using that detector can minimize that effect and use it more effectively.

Most of us I suspect are running TDI  with GB at around 8 and delay of 10us. I know that not using GB can be used in soils that are not badly mineralized for greater sensitivity. In soils that are not highly mineralized (soil that allows effective use of a VLF machine, for instance), it is better to run on GB Off, or to in GB and use less or more than the usual "8" that balances out perfectly in most conditions, ie. purposely running a bit unbalanced)?

In other words, from your vast experience, are there settings other than those typically used that can "trick" or "fool" the detector to see things it would ordinarily not see (and mask) by varying adjustments that are favored to get a quite, stable threshold and 'quiet running'?" 

If running GB, would under balancing, or over balancing it by a, say, 1/2 or 1 unit result in better detection of small gold (at the cost of noisier or less stable operation).

Or is the best solution with the TDI just to operate in proper GB and "ALL" conductivity and accept that you're just going to miss certain size/shape/character pieces of gold and call it good until one can afford a more modern and more sophisticated detector? 

I guess if I could better visualize the chart you provided I wouldn't ask, as the chart you likely contains the answer, but on the other hand maybe there's a practical-compromise setting that summarizes the best overall performance (minimum blind spot) without multiple passes at different varying settings.

I am not addressing other PI detectors w/ regard to settings because I haven't used them, but if you have suggestions for other common machine settings to get the most from, I know that insight would be most welcome. Being able to have and use a GPZ7000 would be great to aspire to, as for now it's likely the best of the best and most capable "one-pass" unit on the market, albeit it at a price point relatively few can justify.

 

Thanks,

Bob

  • Like 1
Link to comment
Share on other sites

The problem with the TDI SL, and I don't know if it exists with the other TDI models, is that the GB "range" is fairly wide. Much moreso than VLF units. I installed vernier controls on mine, so I could easily obtain a GB setting that just "barely" quiets my detector. I think it makes a difference.

Jim

  • Like 2
Link to comment
Share on other sites

2 hours ago, Jim in Idaho said:

The problem with the TDI SL, and I don't know if it exists with the other TDI models, is that the GB "range" is fairly wide. Much moreso than VLF units. I installed vernier controls on mine, so I could easily obtain a GB setting that just "barely" quiets my detector. I think it makes a difference.

Jim

On my Gen 1 TDI, that GB range is VERY wide and poorly defined, meaning when balance is achieved (NO sound when pumping) a setting either side of that perfect balanced center is also quiet before you start getting the tone-up (when the coil is lowered when pumping) as you turn the knob counter clockwise, and going clockwise before you hear the tone-down as you lower the coil when pumping.

A hypothetical could be where pumping, the detector goes silent and no longer produces a higher tone as the coil approaches the ground (balanced) at knob position "7.5," but if you keep rotating the control clockwise, it stays silent (balanced) until you reach "8.5", at which point you start hearing the low tone approaching the ground with the coil. That 7.5 to 8.5 position is pretty wide. Maybe if I were in extremely mineralized soil, the balance knob setting becomes more critical/precise- I don't know because I have not operated the TDI in such conditions (Australia seems to have HEAVILY mineralized soil, for instance, much more mineralized than where I've tried the TDI here in Arizona).

If I read you right, you have found that the LOWEST GB knob setting (most counter clockwise) that produces silence when balancing makes the detector the most sensitive? And conversely as you rotate the knob clockwise, just as you approach hearing the tone-down when pumping is LESS sensitive? (In the hypothetical example I used above, that would mean using the 7.5 setting, as it is the lesser "barely balanced" setting you describe?)

Of course Gen 1 does not have a vernier GB, perhaps because the GB is not to touchy (critical) in finding the quiet GB position. Having not used a SL, I am guessing here.

Another question about GB: If in unmineralized soil, running GB OFF results in a single tone response to all metals, but they say it makes the detector more sensitive to deeper targets. The criteria for turning it OFF is that when attempting to ground balance, there is NO position at which you can null out the detector, meaning there is no balance point by varying the knob position w/ the GB switch ON.

If you CAN ground balance in GB ON (meaning you have mineralized soil), the manual says you "must" use GB ON. My question is, In MILDLY mineralized soil where you can find a ground balance (twisting the knob does something), but it's not so mineralized to where a VLF cannot be used effectively (indicating not BADLY mineralized ground), will running with GB OFF be productive at all, or more sensitive/deeper than with it ON?

I apologize if my questions sound "muddy," but trying to put into words in text that precisely mean what I am getting at is difficult. It's one of those situations where it takes a thousand words in print to say what you could describe in person in about 15 seconds.

 

Link to comment
Share on other sites

"Of course Gen 1 does not have a vernier GB, perhaps because the GB is not to touchy (critical) in finding the quiet GB position. Having not used a SL, I am guessing here."

Actually, the Pro version of the Gen 1 (made for Australian use) has a "fine adjust" control. And, the more GB you dial in, the less sensitive it is. In effect, you are telling your detector to ignore a greater range of signals. The less GB you can use, along with having a stable machine, the better.

Jim

Link to comment
Share on other sites

On 3/24/2023 at 2:21 PM, Steve Herschbach said:

taking a detector like a GPX 5000 and running multiple times with multiple settings tends to find a few missed nuggets.

?

Link to comment
Share on other sites

6 hours ago, bobinyelm said:

Another question about GB: If in unmineralized soil, running GB OFF results in a single tone response to all metals, but they say it makes the detector more sensitive to deeper targets. The criteria for turning it OFF is that when attempting to ground balance, there is NO position at which you can null out the detector, meaning there is no balance point by varying the knob position w/ the GB switch ON.

Another question that Steve H. has answered, and it's also in the 'Guides' section of this site:

 

  • Like 1
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...