Popular Post Steve Herschbach Posted August 9, 2017 Popular Post Share Posted August 9, 2017 I purchased a Golden Mask telescoping rod with the intent of using it for my Deus HF elliptical coil. XP placing the battery in the trapezoidal lower rod section however made an adaptation more trouble than it is worth for something I am not sure I will keep anyway. I decided to repurpose it instead to the Minelab Gold Monster 1000 in an attempt to make it as easy as possible to collapse down and put in a rucksack. The arm cup removal is easy. Just remove the bolts. The grip/handle however is both screwed together and glued. Have to give them credit - beautifully made rod assembly. Some heat from a hair dryer and careful prying got the grip assembly off the rod. The upper rod is thicker than the standard rod diameter and so the neat little clamps Minelab includes with the GM1000 will not work. Instead standard hose clamps will serve until I get some that fit better. The upper rod is not quite long enough to get the proper spacing for the armrest, so this is a mockup until I find a short piece of rod the correct diameter to install in the upper rod for a little extra length. Roughly 30" long when collapsed. The coil needed to be shimmed with an extra rubber washer. I used the skinny little Golden Mask plastic bolt but will drill the isolator rod out to accommodate the Minelab bolt later. Near final product, with way more length fully extended than I need at my height of 5'11" but that is good for working overhead cut banks and poking around in the brush. Click all photos for larger versions. Once I get the rough edges finished this will be a sweet little backpacker unit. 11 1 Link to comment Share on other sites More sharing options...
Shasta gold hunter Posted August 9, 2017 Share Posted August 9, 2017 Sweet setup! Looks like something I may like to do. Thx for sharing. Link to comment Share on other sites More sharing options...
Hobo Posted August 9, 2017 Share Posted August 9, 2017 Steve, where did you buy the Golden mask rod? Thanx,,.......... D. Link to comment Share on other sites More sharing options...
Steve Herschbach Posted August 9, 2017 Author Share Posted August 9, 2017 Only place I could find it was direct from Bulgaria on eBay. Had no issue, prompt delivery, excellent product. Price went up a little since I bought it. http://www.ebay.com/itm/Universal-Golden-Mask-Telescopic-Handle-for-metal-detectors-/122630034975?hash=item1c8d51d61f:g:PMwAAOSwrhBZGedY http://www.ebay.com/itm/New-Universal-Golden-Mask-Telescopic-Handle-/263083698389?hash=item3d4102a8d5:g:BxEAAOSwQJhUi43Y Link to comment Share on other sites More sharing options...
RickUK Posted August 9, 2017 Share Posted August 9, 2017 The 2nd supplier is the one that i bought my GM shafts early last year,use mine all the time on my Deus,terrific shafts especially for the Deus coil,as i mainly just use the detector without the controller as i usually have mine in my pocket and just use it as a audio only machine. But must admit i love the way that Steve has grafted the Gold Monster control box onto the shaft,work and looks very well. 1 Link to comment Share on other sites More sharing options...
Steve Herschbach Posted August 10, 2017 Author Share Posted August 10, 2017 Almost there. Better fitting clamps, upper rod extended 6" with 3/4" PVC pipe, and drilled to fit Golden Mask armrest. About 32" collapsed and 5 feet fully extended! Weighs 3 lbs 7.7 oz (3.48 lbs) or 1.58 kg with rechargeable batteries installed. A few little tweaks yet to do but basically this is a done deal. 1 Link to comment Share on other sites More sharing options...
Hobo Posted August 11, 2017 Share Posted August 11, 2017 Thanx Steve, I like the compactness of it. Link to comment Share on other sites More sharing options...
Sourdough Scott Posted August 11, 2017 Share Posted August 11, 2017 Gold Monster fitted with a bamboo shaft. Very lightweight. Just a little bit of sanding to make it easy for the stock clamps to fit. The Jungle Monster. 4 Link to comment Share on other sites More sharing options...
Norvic Posted August 13, 2017 Share Posted August 13, 2017 A tit bit, when I modded the Monster as a pinpointer, I accidently found ML have molded a clip into the support that goes up to front of battery holder. This clip holds the coil cable neatly and firmly as it heads towards the shaft a 4 or so inches from where it screws into the control box. Have again attached the photo of the Monster Pinpointer to illustrate this. 5 Link to comment Share on other sites More sharing options...
Norvic Posted August 13, 2017 Share Posted August 13, 2017 Only to commoners Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now