MCH2
Full Member-
Posts
52 -
Joined
-
Last visited
Content Type
Forums
Detector Prospector Home
Detector Database
Downloads
Everything posted by MCH2
-
‘CTX TONES’ Detect Mode: Park 1 Ground Balance: 0 (Factory pre-set) All-Metal (Horseshoe): On Frequency: Multi Volume Adjust: 20+/- (Depending on your hearing) Tone Volume: T1=4, T2=25 Sensitivity: 20+/- (Depending on your search environment) Recovery Speed: 6 Iron Bias: 6 Target Tones: 50 Tone Break: T1=1, T2=12 Tone Pitch: T1=1, T2=20 Threshold Level: 8 Threshold Pitch: 4 Discrim Break accept/reject: None (All Metal) This setup was programmed to get the Equinox to sound as close as I could possibly get to a CTX3030. The tones will closely match the CTX3030 (i.e. small hammered coins will have a low tone, large copper coins a high tone), although the audio responses will sound flat in direct comparison. These settings will allow you to use multi-tone in All-Metal, giving an audio discrimination (lower volume for rejected items). Although this program was designed just for the tones, it is powerful and you can try it on different environments to see if it works for you. Doesn't "Target Tones of 50" have only 1 tone break?
-
A soak in vinegar will take the rust off nicely. Check every few hours.
-
I sent my 600 back and got a replacement pod. The headphones work well, have a nice tone and strong sound, but after putting them on and taking them off a few hundred times they broke near the pivot point where the headband piece connects to the actual earmuffs. I wrote a review (with pics) on Amazon and the company sent me another pair. I went and strengthened the second pair before there were problems in this area. Not pretty, but solid. 🙂
-
That appears to be a hand-forged trap of considerable age.
-
I could give you a better estimate to it's age if you cleaned it up further. Try using a stiff nylon or better yet a brass wire brush on it. I can safely say you will not be ruining any value by doing so with this trap in this condition. Try at least to get the pan looking better. The pan often has the brand stamped into it. It appears there is a hole (should have two) in the pan from the pic. If so, it was manufactured that way by a couple different makers to hold bait.
-
Gold Coin Find Most Of Us Never See Indian Princess
MCH2 replied to Gerry in Idaho's topic in Minelab Equinox Forum
Very rare find! -
Very nice.
-
Far from an expert, but for coins, this works well for me. Sensitivity depends on situation (usually 16 - 22). Equinox 800.
-
Has Anyone Tried These Waterproof Headphones?
MCH2 replied to NCtoad's topic in Minelab Equinox Forum
Work well; nice and loud. The cord is long enough to plug straight into your machine without your headphones being pull off your head. -
Cotton Balls, Q Tips And........
MCH2 replied to normmcq's topic in Metal Detecting For Coins & Relics
Great coin! -
Finally found a high VDI war nickel on 4/17/19. This one reads 20 on the Nox in mulit-frequency park 1. Another high reading San Francisco mint nickel. In single frequencies this silver war nickel reads: 5Khz = 14 to 20 VDI (jumpy) 10Khz = 20 VDI 15Khz = 20 VDI 20Khz = 20 VDI 40Khz = 22 VDI
-
23 to 25
-
I have seen a few posts where the 1943 S war nickels especially, read high.
-
Yes, that is the link/thread. I only got part way through it when the site went down for me anyway last night. It is an interesting read. Thank you.
-
Last night I was reading a thread/discussion on the Equinox's multi-frequency parameters. Has the thread gone south, or am I just not finding it?
-
The Minelab Equinox: An Advanced Guide. By Clive James Clynick
MCH2 replied to cjc's topic in Minelab Equinox Forum
Hi, This link should work. -
Looks like your coin on upper right of left-centered pic at this Link.
-
What Vdi Are Your Buffs & V Nics Coming In At?
MCH2 replied to Happa54's topic in Minelab Equinox Forum
-
Appears to be in nice shape. Congratulations
-
Fisher F-Pulse Following
MCH2 replied to “Spartan800”'s topic in First Texas - Bounty Hunter, Fisher & Teknetics
Here is another link that may help. - -
Fisher F-Pulse Following
MCH2 replied to “Spartan800”'s topic in First Texas - Bounty Hunter, Fisher & Teknetics
"You all suck! Really no feedback? Ba-humbug!! " Spartan, your a funny guy! I have the Fisher F-Pulse. From my 3 months of using it I can say it is a powerfull unit and I like it, but you need to change batteries after about 16 hours of use if like me you use full sensitivity. After about 16 hours of use it can get quirky and not respond as anticipated. I believe it is a little sensitive to any drop in voltage due to aging batteries. Also, I had to stretch the negative contact spring which is attached to the end cap out as it was making intermittent contact and the unit was malfunctioning even with fresh batteries so watch out for that also. Good hunting, Malcolm