Jump to content
Sign in to follow this  
doc holiday

Why Is Gold A Low Conductor And Silver A High Conductor When

Recommended Posts


The smooth flow of electrons in a metal is the key to high conductivity. In bulk metals the electron shells of individual atoms morph into electron bands. The outer sp bands in copper, silver and gold all conduct well, but can be effected by the next inner d band that can cause scattering (i.e. lower conductivity). “This is least important in silver where the 4d-electrons are about 4 eV away from the Fermi-level (which is also why silver is colorless). But the 3dbands in copper and the 5dbands in gold are closer to the Fermi level (absorption in the blue) and they cause more scattering with the sp electrons.” Silver wins.

  • Like 4

Share this post


Link to post
Share on other sites

The answer you are looking for is both simple and complex.  I will try to explain the simple part.  First, whether a target is a high or a low conductor is determined by the GB control and just where it is set.  If the GB is set so the ground signal is nulled, then any detected object that generates a low tone has a longer time constant than the ground signal.

This results in the GB signal channel being greater than the metal response channel.  Thus, the summed signals results in a negative response, and this results in a low tone.  

In the case of gold nuggets this means the nugget has to be pure enough, the right size and density and often the right shape or right surface characteristics.  Over the years, much of the  gold I found came from Rich Hill AZ.  Fortunately, this gold is quite pure (92% or so).  As such, gold larger than a quarter OZ was large enough to generate a low tone.  All gold smaller would create a high tone,.  Early US gold coins follow this pattern, meaning a $5 US gold coin would or could fall in the GB hole and be almost not detected.  All lower valued gold coins would be a high tone or a low conductor.

As the purity of gold is reduced, the conductivity of the gold diminishes, thus, much if not most is detected as low conductors.  A good example is the gold we found about 5 miles from Rich Hill where all the gold found registered as low conductors even up to the 1 oz nugget found.  At this site almost a pound of gold was found with many of the nuggets greater than 1/4 oz and all tested with the TDI registered as low conductors.

Reg

  • Like 7
  • Thanks 1

Share this post


Link to post
Share on other sites

Finding the amount of reduction of the conductivity of gold as it is alloyed has turned out to be quite difficult.  Fortunately, I did find some shocking information on the old PI forum that does help.  Here is that info.

Eric
Here are some numbers for copper-gold and silver-gold alloys.
The first column is the % of gold in the alloy.
The second column is the conductivity relative to copper of the copper-gold alloy.
The third column is the conductivity relative to copper of the silver-gold alloy.
% au cu ag
100 .75 .75
90 .14 .23
80 ??? .17
70 .11 .14
60 .12 .14
50 .14 .15
40 .17 .17
30 .22 .21
20 .30 ???
10 .47 .44
0 1.0 1.05
Lead shot is usually alloyed with antimony, so its conductivity is less than pure lead.
Robert

(The above info was posted by  the late Robert Hoolko).

Hi Beachcomber,
Alloying even a few percent of other metals causes the conductivity of gold to drop dramatically. Even if the other metal is a good conductor, like silver. I haven't seen any published values for the different alloys either. I have a conductivity meter which gives a reading as a percentage of that of annealed copper. A 9K ring gives a reading of 18%. Unfortunately the object has to have a surface area of about a square centimeter, otherwise you do not get enough signal to read. This is a very wide ring, so it can be done. No other rings I have work. Great for coins though, a nickel reads 5.3%
Eric.

 

As an example from the chart we see that gold can go from a reading of 77 at pure gold to 16 when alloyed with silver such that the gold is only 75%. The 16 reading would place that same gold closer to the conductivity of lead, while the pure reading is much closer to copper.

This last post refers to a website where standardize gold alloys were listed by a company, deringerney, in 2010.

Hope this info helps.

Reg

  • Like 3

Share this post


Link to post
Share on other sites

Thanks everyone for your informative replies---I think the takeaway from all this is Dig Everything when gold hunting.

Share this post


Link to post
Share on other sites

Thanks Reg, this helps explain why gold has such a wide response on my CTX 3030 screen. 

Share this post


Link to post
Share on other sites

FWIW, it seems that silver production was down last year as high-producing lodes are increasingly hard to come by. 

The argument has been made that there will be VERY little relatively easily mineable silver left on the planet in a few decades. 

It's also claimed that at any given time there may actually be more above-ground useable non-bullion gold on Earth than silver because most gold is kept "intact" i.e. not used in manufacturing but instead kept as jewelry or bullion; OTOH, most non-bullion silver is used-up in manufacturing. The silver bullion market is incredibly small compared to gold.

Remember a few years ago when waste companies would offer free "recycling" of old computer motherboards? They were doing that to salvage the tiny amounts of gold those motherboards contained. Since silver is only about 1/80th the price of gold on an ounce-to-ounce basis at this time it's just not worth it from a financial standpoint to salvage all the silver deposited in landfills across the nation. If silver rises to a few hundred dollars per ounce, as some speculate it eventually will, it might be a good idea at that point to invest in companies specializing in the recovery and recycling of silver used-up in manufacturing. Some financial experts say that the "normal" ratio between gold and silver in terms of price should be more along the lines of 1:15 than the present 1:80. Time will tell. If it does, look for metal detector companies to begin marketing machines specializing in finding silver.

  • Like 1

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Similar Content

    • By Steve Herschbach
      I have used many metal detectors over the years, and right now I have to say that the new Makro Racer 2 has perhaps the easiest to understand, best laid out, most practical display and menu system I have ever seen in a top end detector. Now, you can sure say you hunt by ear and do not need a screen and I get that, but if we are going to put a screen on a detector, then let's do it right.
      Simple detectors with few functions are easy to make screens for - there is not much you need. But even then just the basics are often wrong. Machines that feature target id numbers, what is the thing you will most look at on screen? The target id numbers! Yet these are often way too small or off to the side as if an afterthought.
      The Makro Racer 2 id numbers are huge, much larger than on the original Racer and Gold Racer, which are already good sized. The number 88 display in the diagram above is fully 1.5" x 1.5" in size in real life. Other machines have some pretty big numbers but I think this sets a record as I can't think of any machine with larger id numbers on screen though some are close.

      Makro Racer 2 LCD display and controls

      Makro Racer 2 screen layout

      Makro Racer 2 screen and control descriptions
      The number can be the ground balance number, target id, or depth reading. You get a text display just above the number confirming which it is. Below the numbers are three zone references, Fe, Gold/Non-FE, and Non-Fe, that are used to set tone breaks and audio for the three main zones or bins as they are sometimes called.
      Another basic feature lacking on a lot of machines - the meter backlight. With the Racer 2 you get off, intermittent, or full time backlighting, and it includes the translucent red control buttons. The control ranges between 0-5 and C1-C5. At 0 level, the keypad and display backlight are off. When set between 1-5, they light up only for a short period of time when a target is detected or while navigating the menu and then it goes off. At C1-C5 levels, the keypad and display will light up constantly. I do not know of anyone doing a better backlight.
      The right side of the meter is informational - ground phase (ground balance number), mineral % (ground magnetite content), coil warning notices, and a six segment battery meter.
      Across the top below the 0 - 99 reference sticker, is a series of 50 "bullets" each of which covers 2 target id numbers. Open bullets (which appear gray in the diagram but are invisible in real life - see top photo) indicate accepted target id numbers. Blacked out segments show what discrimination and notch setting you have programmed in a single quick glance. When a target is detected, the big number on the display will be mirrored by one or more of the bullets flashing dark.
      The four control buttons are simple as can be - up and down takes you through the left hand menu area. Right or left lets you set each function selected by going up and down. The menu is basically the entire feature list just laid out right there for you to see. You want to know what this machine can do, just look at the screen. Most other machines you have no clue without reading the owners manual or at least pushing buttons to see what functions appear.
      Some settings like the backlight are system wide for all modes. All other settings like Gain are independent in each mode, and can be saved independently in each mode. This means you can play neat tricks like setting up a couple modes with dramatically different settings and then flip back and forth easily between two modes for target checking.
      You even get to decide what mode is the default start up mode. The Racer 2 starts up in the last mode where the save function was performed. If you always want to start in Beach mode, just modify and save something in Beach mode. Next time you start the detector, you will be in Beach mode.
      It is simple. It makes sense. No cryptic abbreviations or acronyms. No sub menus. It is, in metal detector terms, a work of art. Whoever designed this should sign it so I can frame it and hang it on my wall.
    • By Steve Herschbach
      First Texas (Bounty Hunter, Fisher, Teknetics) - last new models Fisher F75+ and Teknetics T2+. Next up a new pulse induction (PI) beach detector. A new digital multifrequency to replace the Fisher CZ3D is long overdue but at this rate we will be lucky to just see the PI before the end of the year.

      Garrett - last new model the AT Max. Hard to believe the flagship GTI 2500 has been around since 1999 with no updates. Garrett so far has shown no interest in multifrequency. The most I was hoping for was a lightweight dry land version of the ATX, but so far no sign of that happening either. I doubt we will see anything else from Garrett this year but they could surprise.
      Makro - last new models the Multi Kruzer and Gold Kruzer. Makro has mastered single frequency so everyone would like to see what they can do with multifrequency or pulse induction. I expect Makro is done with new models for the year.
      Minelab - last new models Equinox 600 and 800. I have no idea what’s up next for detectors but I sure would like to see that small coil for my GPZ 7000. I really don’t expect anything new for the rest of the year besides Equinox accessories.
      Nokta - sister company to Makro. Last new detector the Nokta Impact. I actually bet on a PI under the Nokta brand rather than Makro brand simply because the Nokta housings like the new Impact housing would better contain a high power PI.
      Tesoro - Who? What?
      White’s - last new models the MX7 and TDI SL Special Edition plus the just announced Goldmaster 24K. Hopefully that new tech will eventually see the light. Right now just getting the 24K out the door is job one.
      XP - last new products the HF coils for the Deus, with X35 coils due by end of year.
    • By Steve Herschbach
      Our cup runneth over!
      Just a few years ago the market for "over 30 kHz nugget detectors" was quite limited. For a long time there were only a few options:
      Fisher Gold Bug 2 (71 kHz) $764 with one coil
      Minelab Eureka Gold (6.4, 20, & 60 kHz) Discontinued $1049 when new with one coil
      White's GMZ (50 kHz) Discontinued $499 when new with one coil
      White's GMT (48 khz) $729 with one coil
      Things were that way for over a decade. Then in 2015 Makro introduced the Gold Racer (56 kHz) $599 with one coil. Sister company Nokta released the AU Gold Finder (56 kHz) $799 with two coils
      Then in 2017 we see the Minelab Gold Monster 1000 (45 khz) at $799 with two coils. And although not a dedicated nugget detector, the Deus high frequency coil options (up to 80 kHz) were also released, $1520 for complete detector with one HF coil.
      Now in 2018 we get another general purpose machine, the Equinox 800, that can hit 40 khz, $899 with one coil. And just announced...
      the Makro Gold Kruzer (61 kHz) $749 with two coils and
      the White's Goldmaster 24K (48 khz) $749 with two coils
      These last two announcements have made barely a ripple in the prospecting world, or at least going by other forums that seems to be the case. There are various reason for that (forums not being prospecting oriented or being Minelab centric) but still the lack of buzz is interesting. I do believe people are both burned out by all the new introductions and that the market is saturated with high frequency models. Leaving out the general purpose machines to sum up the current options it looks like the current "sweet spot" for pricing is a high frequency model at $749 with two coils.
      Makro Gold Racer 56 kHz - $599 one coil
      White's GMT 48 khz - $729 one coil
      White's Goldmaster 24K 48 kHz - $749 two coils
      Makro Gold Kruzer 61 kHz - $749 two coils
      Fisher Gold Bug 2 71 kHz - $764 one coil
      Minelab Gold Monster 1000 45 kHz - $799 two coils
      Nokta AU Gold Finder 56 kHz - $799 two coils
      High Frequency Gold Nugget Detector Roundup

    • By ☠ Cipher
      Here's another, a second interesting product I've run into recently. This one has a bit of a giggle factor for me, but I could be wrong. See what you think.
       
    • By Mxt Sniper
      Someone has X-rayed a equinox coil. Pretty good sized circuit board inside!
      https://md-hunter.com/minelab-equinox-coil-x-ray-is-it-really-the-half-of-machine/
×