microsniper Posted December 12, 2019 Author Share Posted December 12, 2019 UPDATE: Minelab just replied to my coil repair inquiry. "Unfortunately there is no repair for your damaged coil. They (the repair techs) are unable to perform a repair or replacement of the coil plug connector." Sooo... your on your own if you damage the connector, which in my opinion is too easy to do. I was actually worried about doing just that when i first bought the EQ. Ill update as soon as I get around to performing the fix with the new connector. If anyone has more tips/tricks or product recommendations to use for this fix please post them. In the mean time here is the last batch of EQ600 nugglets (before the accident) that were found by my competition.....I mean girlfriend, and I Link to comment Share on other sites More sharing options...
fredmason Posted December 12, 2019 Share Posted December 12, 2019 Doing good on the Gold! If they can’t repair a connector , how do they Fix anything else? just to keep from a similar problem, how did that happen? did you slam a door on it, I did that once or twice back when I was young and in Too big of a hurry! fred Link to comment Share on other sites More sharing options...
microsniper Posted December 12, 2019 Author Share Posted December 12, 2019 Thanks Fred, funny enough I just bought a nice padded case for the back of the truck to carry the detector(S) in..to protect them! I think it was just the bouncing around on the back roads that did it.... Link to comment Share on other sites More sharing options...
microsniper Posted February 29, 2020 Author Share Posted February 29, 2020 FIXED!!! Ok, so I finally got around to doing the coil repair. Not the most professional soldering but it got the job done. Items needed: Soldering iron and solder Plumbers flux wire snippers/strippers Liquid Tape and fine -cheap paint brush dual wall heat shrink tubing (two sizes. one the same size as coil cable, and one size larger) Optional: Jewelers glasses, third hand tweezers. Made it much easier to see and hold things in place. Six very fine wires and two shielded wires in the center. I stripped back and separated the two inner wires first, making sure to leave a little bit of the plastic shielding on each side so they would not make contact while soldering. trimmed all wires to about the same length so they would all line up when soldering. Then Fluxed all the wires, tinned them very carefully with a touch of solder. (I could have done a better prep job and taken more photos but i was motivated to just get it done before dinner) I soldered the innermost wire first (to establish the length of the other wires and because its strong and held every thing together) Then soldered the surrounding red wire. Trimmed and soldered all the others. Painted Liquid Tape on all soldered areas, and put extra around and between the two inner wires. I finished it off with the dual wall heat shrink tubing..... and Viola! The coil is back in action!! I dont think I would trust it to be submerged in water ever again, but it seems to be bomber enough to take some rain or a quick splash. Im sure I could have taken more time and done a cleaner job but it seems to work just fine. Ill test it out in the field and report back if there are any sonic anomalies, bump sensitivity, etc... Thanks again for hooking me up the connector Steve! Link to comment Share on other sites More sharing options...
TedinVT Posted February 29, 2020 Share Posted February 29, 2020 Nice job! Came out looking good. Tnx for the photos & details Micro. Link to comment Share on other sites More sharing options...
Steve Herschbach Posted February 29, 2020 Share Posted February 29, 2020 4 hours ago, microsniper said: Thanks again for hooking me up the connector Steve! It's doubtful I ever would have used it so I'm glad it worked out for you. Link to comment Share on other sites More sharing options...
nordic Posted March 2, 2020 Share Posted March 2, 2020 Never heard of liquid tape! Good to know. I think the most important wire there, in terms of insulation, is the core of the shielded wire. It is the positive TX signal which is very powerful and probably will damage something if there is a contact. When Nox turns on it fires the TX signal at a reduced strength to check if all is good (not shorted, etc). After that, it is at full, even if the short occurres. Link to comment Share on other sites More sharing options...
All Digger Posted February 4, 2021 Share Posted February 4, 2021 On 2/29/2020 at 8:49 AM, microsniper said: FIXED!!! Ok, so I finally got around to doing the coil repair. Not the most professional soldering but it got the job done. Microsniper can you remember how manny wires was on the coil connector? is it 7 or 8 pins because in the pics i can see only 7 and its supposed to be 8, im trying to make an extension cable connector for my equinox 800 because basically the coil cable its to short and im going to try to make a extension cable with waterproof connectors for it im trying to find a connector online, thank you for the pictures and very nice job fixing the connector . Link to comment Share on other sites More sharing options...
rvpopeye Posted February 6, 2021 Share Posted February 6, 2021 I just checked mine and it's 8 pin. 7 outer and 1 in the middle. Be careful to note where the indexing notch is . We used to call these connectors DIN in my world. There's probably a 4 or 5 pin on your old CB mic. If I had a nickel for every time I forgot to put a connector cover or some heat shrink on before starting to solder..........I wouldn't care about gold ! LOL I started my tron life at 12yo ! Liquid tape is "the balls" as one of my friends used to say. (Use a little around the ends of the heat shrink unless it's the kind that has sealer inside to add a bit more waterproofing , ). OH and ML not wanting to fix that connector probably something about waterproofing ? Or doubts of consumer doing the soldering. Link to comment Share on other sites More sharing options...
Cwebbstar Posted November 28, 2021 Share Posted November 28, 2021 Can someone sell me one of them connectors for the 800 I just broke mine Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now