TedinVT Posted July 30, 2020 Share Posted July 30, 2020 10 minutes ago, Canarias_detection said: Good answer ... I would have to try another from someone ... I have not tried another detection mode ... right now I have it in v2 but it does not work very well ... it does not identify targets as before ... soon I will upload videos ... Could it be a problem with a damaged plate? Like others, I doubt the problem is being caused by the new firmware version. If water, especially saltwater, leaked into your coil that could be a likely cause. Try the other detect modes to see if the problem occurs across all 8 detect modes. If it does, try to hook up to a friend's coil and see if that eliminates the problem. I bet it does. Either way you'll probably end up shipping the control pod and your coil to Minelab for warranty replacement. They will need both pieces to confirm the problem. Good luck. Link to comment Share on other sites More sharing options...
Canarias_detection Posted July 30, 2020 Author Share Posted July 30, 2020 8 minutes ago, TedinVT said: Like others, I doubt the problem is being caused by the new firmware version. If water, especially saltwater, leaked into your coil that could be a likely cause. Try the other detect modes to see if the problem occurs across all 8 detect modes. If it does, try to hook up to a friend's coil and see if that eliminates the problem. I bet it does. Either way you'll probably end up shipping the control pod and your coil to Minelab for warranty replacement. They will need both pieces to confirm the problem. Good luck. ok perfect..thank you very much for the solution..I'll upload videos soon so you can see it..a pleasure Link to comment Share on other sites More sharing options...
mn90403 Posted July 30, 2020 Share Posted July 30, 2020 Do you only have one coil? Link to comment Share on other sites More sharing options...
Canarias_detection Posted July 31, 2020 Author Share Posted July 31, 2020 9 hours ago, mn90403 said: Do you only have one coil? yes only one Link to comment Share on other sites More sharing options...
Canarias_detection Posted August 4, 2020 Author Share Posted August 4, 2020 hello please check video in first page..thanksI still have problems with stability Link to comment Share on other sites More sharing options...
Steve Herschbach Posted August 4, 2020 Share Posted August 4, 2020 It does not seem like the update is the issue. More like you are on mineralized beaches and need to use Beach 2 and lower your sensitivity. That is what the overload symbol is telling you. It senses when there is too much signal blowback from saltwater or black sand or both. When a detectors "sees" too much salt or too much black sand (or both) it will go totally blind unless the transmit signal is reduced. Going into overload is not reducing depth - it is giving you depth when the machine would otherwise be non-functional. The overload will not go away until the conditions creating it go away. The only time I have seen the overload signal is when crossing areas on a beach obviously loaded with magnetite. The overload symbol comes on and the detector keeps running fine, then the symbol goes away once past the magnetite patch. You May also be suffering from salt water intrusion in the detector or the coil itself, which is in turn causing the signal to occur. Contact Minelab Service if you think you have a defective detector. Difficult Areas – Black SandSome beaches contain black sand, which has high natural iron content and is often magnetic. This causes continuous false ferrous detections, making normal beach detecting impossible. Beach Mode automatically senses black sand and reduces the transmit power to ensure that targets can still be detected without overloading occurring. When black sand is sensed, the Beach Overload Indicator will appear on the LCD. When this icon disappears, full transmit power automatically resumes. Link to comment Share on other sites More sharing options...
Canarias_detection Posted August 4, 2020 Author Share Posted August 4, 2020 1 hour ago, Steve Herschbach said: It does not seem like the update is the issue. More like you are on mineralized beaches and need to use Beach 2 and lower your sensitivity. That is what the overload symbol is telling you. in the video used mode beach 2.. I understand, but the triangle does not appear anymore, it only appears with version 3. Now many false signals without stability, I have cleaned the coil, removing the protector and I have to try it again Link to comment Share on other sites More sharing options...
Steve Herschbach Posted August 4, 2020 Share Posted August 4, 2020 It may be that the triangle is supposed to be appearing, that you have difficult conditions, and need to lower your sensitivity. Link to comment Share on other sites More sharing options...
Canarias_detection Posted August 4, 2020 Author Share Posted August 4, 2020 1 minute ago, Steve Herschbach said: It may be that the triangle is supposed to be appearing, that you have difficult conditions, and need to lower your sensitivity. I lowered the sensitivity to 15 ... the problem remained the same ... I will try in the field or different beach sandThank you Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now