Jump to content
JustSwell

Digging Safety? Utilities? War Stories?

Recommended Posts

This may sound like a dumb question but I'm new to detecting and haven't really found many talking about where and when it's safe to dig.  If this is posted in the wrong place, please do move it.

When digging within city limits, parks, yards, in green strips along sidewalks, what about public utility lines, phone lines, or plastic gas lines in yards.  How much of this are some of you concerned about?  Do you have any "war stories" to tell?  Any best practices for safety in this regard that you could share?

Share this post


Link to post
Share on other sites

Most digs are 8" or less. The deepest hole may go all the way to a foot. The chances of hitting something dangerous at less than a foot are so slim as to be non-existent. After 45 years of detecting I never give it a thought. The biggest danger is old war zones and finding live artillery rounds but I have never heard of anyone actually getting blown up.

Share this post


Link to post
Share on other sites

In NZ they run a layer of bright orange tape saying DANGER WIRES BELOW so if you ever strike the tape digging you don't dig deeper, although the wires are still a long way down so you wouldn't normally dig that deep anyway and you just stop if you ever hit the tape.  I struck that tape once a few weeks ago but it wasn't metal detecting, it was digging in a hedge of plants.  

Share this post


Link to post
Share on other sites

We got our park closed to detecting because people were cutting the poly pipe waterlines with their digging tools.  Not dangerous but something that was probably less than a foot....

Share this post


Link to post
Share on other sites

The one utility line I've noticed close to or even on the surface is cable TV lines.  I'm pretty sure they are supposed to be deeper, but it's kind of a free-for-all in that business (in case you don't see TV ads...).  A bigger concern for me on public property is whether or not I'm allowed to dig at all.  But just about every US muni/county/township/parish has a website so I just go there and find out the rules.  If they don't say I can't, I assume I can.  I don't stir up a hornet's nest by calling and asking.  If you've been around long enough (as in "didn't just fall off the turnip truck") you know what I mean.

 

Share this post


Link to post
Share on other sites

As a former State Manager in the underground utility locate profession I have seen many shallow cables and pipes hit by homeowners. When in doubt call your states local one call center. It's free.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By GlazedTofu
      Found at old pre 1900 coal mining ghost town in Washington state.  I have no idea how old this is but we did have a lot of Chinese miners at this site. 
       
      Anyone have some some knowledge I’d love to hear it!


    • By Propjob
      Well , I was using explorer xs to work in the test garden and noticed half the screen went out. Discovered that a couple of the plastic bosses  for the screws in the control head had broken, allowing the pc board to separate.  On last ditch effort to repair would be to replace plastic control housing if cost effective. So looking to purchase a front half for the control housing..  This is the plastic that the keypad attaches too.  I would consider a parted machine if not cost prohibitive.  I am kind of attached to the xs , and was trying to keep as a backup, but I think it is P......d because the nox  is the new kid.  Prop
    • By M1dn1ghtN1nj4
      So my next project is nearly complete already.  I've designed a "mini gold cube".  Same general idea and layout, but each "tray" is only 11" long, and 6" wide.  About half the width of the real Gold Cube.  The underflow loop is exactly the same dimensions as the Gold Cube as well, to make calculations easier.
      I've read that the Gold Cube is set to run on 1100GPH.  Since mine is half that width, I would assume that 500GPH would be fine.  Also, my trays are set at 9 degrees (just how it worked out).
      Is that an appropriate flow rate?

    • By Alluminati
      Here is another one for you guys to figure out. I haven't the slightest clue, this one makes my head hurt.
      It was found in the water. This old bay has an insane asylum built on it dating from the late 1800's. It is also has a ghost town, a failed colonial type trading settlement dating from around 1825. Before that it was a native village but I think it's safe to say this is not native American.
      It has three stars, or starfish? and a small hole on each side.
      It measures about an inch across.
      It weighs about 17 grams but has at least some sand and clay remaining inside.
      There is no way you guys are going to guess what it is.


    • By Hard Prospector
      I've been a dedicated White's guy for over 20 years of detectors;  GM VSAT,  GMT,  MXT,  TDI, TDI SL (X2) , TDI PRO, SGT and the GMZ....(remember that detector?) so I suppose I feel just a bit  "entitled" to talk a little bit  $h*T  here.  I  know the company's gone through engineering and management upheavals in recent years anyway,  staying  loyal to this company as been a tough journey.  I'm glad they finally  did something to up date the Goldmaster series with the 24k. Five to ten years too late......maybe and time will tell. The industry has changed in a big way in just the last year.  Too bad they couldn't have also made the appropriate  power and tuning up grades to the TDI SL  as well  (which has already been done  by talented do - it- yourself tinkerers out there and sold on ebay).  I know the SL now comes with new paint and a straight rod ......so what!  I just could not wait any longer and anyone who watches the classifieds has seen my TDI fire sale  recently. Sorry for the "sour grapes attitude" but I just had to vent. On a more positive note  and for this single frequency detector,  I can see the 24K showing good promise in tailing pile work.  Sorry for the rant,  its been building for a LONG time! 
    • By Alluminati
      Today I had a look at the shaft that my father put together for his 800. I thought it turned out very well, so I thought I would take a few pictures to share here.
      We looked at a few options but ultimately thought a true one piece shaft was best and easiest.
      Based on a previous conversation I had with an experienced water hunter on here, we figured it would be alright to run the carbon fiber almost all the way to the coil.
      The lower fiberglass factory shaft was cut down to about 6" and secured into the inanimate carbon tube with epoxy. This, along with the lack of clamps really reduced the weight. A couple of holes for the armrest and pod completed the project. Looks like he even got the button on the end of the shaft too.
      I will be doing something similar with mine, although I still think I want to try a kevlar shaft just for fun as it is basically transparent to RF.
      I'm in the process of finding one with the right diameters tonight. The main thing for me is to get the 0.875" O.D. (~22mm) to fit the pod, i can modify the lower piece if need be, or print a new one.
      I'll also tilt the handle a little bit towards myself.
      I love this because it is light and simple.


       

×