billdean Posted November 15, 2021 Share Posted November 15, 2021 Each time I try and ground balance my 6000 there is no detectable change. While holding the GB button I pump the coil then move it side to side. It’s like it don’t work. I friend of mine says his does not either. What am I missing? I run in manual mode with the threshold on. The noise cancel works very well. Link to comment Share on other sites More sharing options...
1515Art Posted November 16, 2021 Share Posted November 16, 2021 I ground balance religiously at start up and occasionally while detecting and don’t notice much if any difference, I kind of assume the auto ground balance is simply very fast and the 6000 acquires a ground balance immediately on start up or is something else going on? Link to comment Share on other sites More sharing options...
billdean Posted November 16, 2021 Author Share Posted November 16, 2021 34 minutes ago, 1515Art said: I ground balance religiously at start up and occasionally while detecting and don’t notice much if any difference, Exactly….Does the 6000 auto GB in manual modes? Link to comment Share on other sites More sharing options...
1515Art Posted November 16, 2021 Share Posted November 16, 2021 Yes, I believe the geo sense is part of the magic optimizing the settings in all modes? Link to comment Share on other sites More sharing options...
1515Art Posted November 16, 2021 Share Posted November 16, 2021 Thinking about your question a little more I wonder if the effect of the geo sense really only makes it appear to the user that the detector is not reacting to ground balancing because the geo sense software is compensating for the GB being off by adjusting gain and other settings maintaining relatively steady ground noise while in the background ground balancing is directly affecting performance? Link to comment Share on other sites More sharing options...
Jonathan Porter Posted November 16, 2021 Share Posted November 16, 2021 If the mineralisation is low then there will seem to be little effect. The main thing is to not have much or any signal with the coil being lifted up and then pushed down to the ground again with a movement of say 100mm when there is a big signal and say 40mm when there is a small or minimal signal. The GPX6000 has a ground balance that is continuous, that is to say it is slowly tracking and compensating for ground signals all the time regardless of the modes used. The Quick-Trak button is for when the ground is extremely variable and the slow auto GB can’t keep up, at start up there can be a big difference in GB if say for instance you have driven hundreds of miles to a new gold field and the ground is completely different etc. A good operator in variable ground will be using the QT button all the time, successful VLF users from days gone by will know all about keeping on top of the ground balance as a means of wringing out max performance. When the QT button is depressed the tracking algorithm ramps up really quickly then throttles back over time while the button is triggered, in variable ground it pays to keep the coil controlled and accurate when pumping so the initial fast GB state doesn’t get knocked off course by excessive movement signal from things like salt ect, always used a controlled measured pumping of the coil just varying the height of the pump if the conditions require it. Usually a good rule of thumb is big signal, big slow pump, small signal, small controlled pumping of the coil. Hope this helps JP Link to comment Share on other sites More sharing options...
LuckyLundy Posted November 16, 2021 Share Posted November 16, 2021 I really noticed the trigger button works best with the DD Coil...Mono, seems to have no effect! Link to comment Share on other sites More sharing options...
billdean Posted November 17, 2021 Author Share Posted November 17, 2021 Thanks Jonathan. That help me understand it much better. Link to comment Share on other sites More sharing options...
Gold Catcher Posted November 17, 2021 Share Posted November 17, 2021 In hotrock rich areas frequent GB can make a big difference. I also wonder if X drift issues are at play with the auto tracking of the 6k. I noticed that the same hotrock can lead to different audio responses when you come back to it. One reason why I like the semi auto GB option of the 7k Link to comment Share on other sites More sharing options...
PhaseTech Posted November 17, 2021 Share Posted November 17, 2021 If you are never getting any signals from the ground, you may want to try the Normal ground mode, as this will give you a little more depth. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now