Jump to content

Recommended Posts

30 minutes ago, cdv said:

I was just asking because of the above post Steve......

Cliff

Good ask... I missed that, and it is news for sure. Was FT going to let the rest of us know?

Link to post
Share on other sites

  • Replies 30
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Popular Posts

Mystery solved. The customer in question asked for 2 coil covers as part of his order. Since they had a couple of prototype covers available - they were shipped. Production coil covers are not yet ava

a disc guard is useless on impulse the resin is very strong and as a general rule, disc protectors should be avoided on a beach finder or stick them and make them waterproof salt and sand passing bet

Yes it's exact, here a FOSTER's coil :

Posted Images

Mystery solved. The customer in question asked for 2 coil covers as part of his order. Since they had a couple of prototype covers available - they were shipped. Production coil covers are not yet available.

My apologies for not clearing this up sooner!!

  • Like 6
  • Thanks 1
Link to post
Share on other sites

I'm a sand scrubber myself so I like using a coil cover even If it does add a little weight...Here's what I use to keep sand/water from penetrating under the coil cover, just run a small bead of this stuff along the open edges and let it cure...

20201008_155556.jpg

  • Like 1
Link to post
Share on other sites

I've used marine epoxy on coils with great success. My only question is...

Does using marine epoxy void the warranty? Unless I heard it directly from FT or Rick, I would not use it.

Link to post
Share on other sites
52 minutes ago, Slimpickuns said:

I'm a sand scrubber myself so I like using a coil cover even If it does add a little weight...Here's what I use to keep sand/water from penetrating under the coil cover, just run a small bead of this stuff along the open edges and let it cure...

20201008_155556.jpg

 

I've done that also and it works.  👍

  • Like 1
Link to post
Share on other sites

I was going thru a couple of coils with the Xcal...... and other machines for beach use a year.   I wear the heck out of a coil cover.   I use LocTite Marine Epoxy....its white so i can tell where the wear is and like was said..... i can put more on as needed.  You can spread it on once mixed with your finger and it dont run all over the place.  Its like 3700 psi strong.   I dont believe anyone would find this a reason not to buy on a resale.   The non-tranferrable warranty would be more likely.

Link to post
Share on other sites

a disc guard is useless on impulse
the resin is very strong
and as a general rule, disc protectors should be avoided
on a beach finder
or stick them and make them waterproof

salt and sand passing between the coil and protecting it
screen and make you lose performance ...

  • Like 2
  • Thanks 2
Link to post
Share on other sites

I'll definitely be wanting a coil cover. There is no resin on earth that will hold up to the rocky beaches I hunt. I hope when they design it that they make it easy to remove for cleaning.

  • Like 1
Link to post
Share on other sites
8 hours ago, dewcon4414 said:

I was going thru a couple of coils with the Xcal...... and other machines for beach use a year.   I wear the heck out of a coil cover.   I use LocTite Marine Epoxy....its white so i can tell where the wear is and like was said..... i can put more on as needed.  You can spread it on once mixed with your finger and it dont run all over the place.  Its like 3700 psi strong.   I dont believe anyone would find this a reason not to buy on a resale.   The non-tranferrable warranty would be more likely.

I want to be clear. When my Equinox coil ears broke my coil was epoxied and brace supports filled with caulk.

Minelab never questioned. I was sent a new coil.  

Dave

 

  • Like 1
Link to post
Share on other sites
On 10/9/2020 at 7:49 AM, LE.JAG said:

a disc guard is useless on impulse
the resin is very strong
and as a general rule, disc protectors should be avoided
on a beach finder
or stick them and make them waterproof

salt and sand passing between the coil and protecting it
screen and make you lose performance ...

I agree whole heartedly. The potting material used is hard as nails and should be no problem, even for rocky beaches. That is unless you swing your coil like a pendulum and bang the hell out of those rocks 😂. I never have used the covers. I have friends who spray truck bed liner ( no metal ) on theirs though with much success. For me though just a waste.

  • Like 2
Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Content

    • By Yellowstone
      Got a desert trip planned in a couple of weeks and was wondering if anyone (Steve especially) has had a chance to test out the AQ for nuggets?  I got mine at the end of September and it has already paid for itself in beach finds, including my first platinum ring ever, a 25.2 gram monster.
      I know it's not designed for prospecting, but was thinking about taking along it to play around.  I did air test a 2.0 gram gold/quartz nugget with Pulse Delay of 7, max sensitivity and minimum ATS and it was a solid hit at 5" and broke the threshold at 7".  For each 1/2 increase of Pulse Delay, I lost about an inch or so.
      If anyone has field experience, I would like to know your results.  I will relay actual findings (if any) after I get back.
      Hope everyone had a great Thanksgiving!
      John
    • By schoolofhardNox
      So the tides were decent enough on my days off to try again for some gold with the AQ or GPX. Since my beaches will not relent with the sanding in, I decided to try another strategy. Day one was split between the AQ for low tide and the GPX for deep silver. With the beach heavily sanded at low tide, all I could do was get some junk jewelry with the AQ. The GPX scored 3 silvers using the monster 18"DD Detech coil. It must have been a sight watching this guy struggle with that coil while holding a side stick and a big spade shovel 😄 The GPX wins that day. But... Day two was raining, so the GPX loses by default ... tough luck GPX (needs to be waterproof, hint, hint) So all day long I used the AQ at another beach which has a decent low tide. But as usual around here, it was sanded in more than ever. Low tide produced very few targets, just 3 zinc cents, some small junk jewelry and bottle caps. It looked like a wasted trip. But I wandered around all over, from high to low tide looking for a break. I knew that the rings were out of reach by the level of the sand against a breaker wall, so I decided to look for small jewelry in hopes of finding a gold stud or even a charm. No luck until I hit a small slope. By this time I had put gold out of my mind and just wanted to dig for the rest of the day. I used the all metal mode exclusively, just to boost the number of targets. I did get a lot of iron and bottle caps but then it happened. I got gold!!!!! No, not Joe or Mitchel kind of gold, 🙄 but more like anything I can get will do gold. So a small prayer necklace pendant shows up. I could tell it was gold right away. 10k it is...my FIRST gold with the AQ. I could now relax. So I started to grid this area carefully and a little while later I got a hit and could see a small bit of the target I thought was going to be a small silver earring.  But it turned out to be a 10k diamond studded Ankh symbol. Looks like a cross with a loop at the top. It's used in ancient Egypt, representing the symbol of life. Gorgeous little piece and my SECOND gold with the AQ. I was in shock. So I start to look around as I am getting back up and about 3 feet from that target I can visually see pieces of a gold rope chain sticking out of the sand. In my moment of professionalism, I tried every combination on the AQ to better find chains......... Actually I just grabbed that thing as fast as I could 😂 So I haven't tried the AQ to see if it actually would pick the chain up or not. But technically not my THIRD gold of the day since it is .925 with 1/12 10K overlay. I think they call that Vermeil. My bad day turned real good, real fast. I hunted a while longer and called it a day.  Thank you AQ for hitting that first gold target and making me stay in that area!




    • By mn90403
      I received my AQ yesterday afternoon.  I put the battery on charger and about an hour later it was fully charged.  After some scrambling around to get out of my apartment I hit the beach on an incoming tide.  I went to an area where I had seen beach PI holes before and decided to give it a try.  As you can see it was not a productive location except for the eCig cartridges which I got 3 of them.  They were deep and the sound was high.
      I started out in everything preset as the Quick Start suggests.  I didn't know what it was going to sound like but it is a higher pitch than I normally listen to.  The waves were making some noise as I was mostly in ankle deep but sometimes knee deep water.  The headphones were comfortable for the 3 hours I was out.  I didn't have a coin for the first 1.5 hours.  I've never had so many bottle caps but I don't hunt this area of the beach.  My deepest target was about 20 inches and was the bottom of the can.  I couldn't find one target at 24" and still digging.  At the end of 2 hours I decided to 'experiment' with going down a notch on frequency delay.  Then on the way back to my start I switched to tone mode.  That was when I heard a 'weird' low tone and when I dug it it was a dime.
      When I first started I had put my cell phone in my top pocket and on the 3rd dig hole it dropped in mud.  Now I have a finicky cell phone that doesn't want to charge properly.  I ordered another BLU phone to replace it. 
      When I put the two shafts together and tried the length I thought it was going to be too long.  It would be if it was a heavy unit but I was able to use the first notch with the push out pin but this would not be good for my wife.  I would suggest that the pin be moved on the lower shaft and also make it shorter.
      It is going to be a learning curve to find a beach that is PI 'friendly' which means that it holds deep jewelry/gold and not just deep trash.
      Mitchel

    • By tvr
      Low water at the local hole today. Low enough that I had wet sand to do some testing with. I can call fish hooks well in the wet sand in all metal ... but not well in the water where I don't have the same ability to change coil speed like over the wet sand. Got lots of lead today, not too many fish hooks other than those attached to rigs with lead or with brass swivels. A couple of deep nickles, one really deep spark plug and one junk child's ring. Was chest deep over a target that sounded really good ... and the battery died. Didn't pack the second one because I had to take care of some other things today, so it was my alarm clock to head home ... and enough of a work out in the shape I'm in. A bit sore this evening, but it is a good sore.
      Cheers,
      tvr
       
    • By cuniagau
      It took me 4 short hunts to finally run the battery down.  Total run time was approximately 11 hours and 35 minutes.  That sure beat the 3 1/2 from the factory battery.  I ran about 95% of the time in AM and only switched to Tone or Mute to check targets. Running mostly presets on the other settings.  The audio of certain targets is starting to become inbedded in my brain now.  Nickels are easy to recognize now.
×
×
  • Create New...